Parts for Frigidaire CPLMV169DCG: 03 - Cabinet Parts

This replacement motor restores reliable rotation to the component it drives—bringing back proper airflow or mechanical movement so your appliance runs as designed and noise is minimized.

• Converts electrical energy into steady shaft rotation to power the attached fan, blower, or mechanism
• Common failure signs: won't start, only hums, stalls, or intermittently runs
• Worn bearings or windings can lead to overheating and reduced performance

• Disconnect power before servicing; if the unit uses capacitors, discharge them per the service manual
• Note wire locations and transfer any brackets, grommets, or fan blades from the old motor
• Mount securely, align the shaft, and confirm correct rotation before finalizing
• Spin the shaft by hand to check for free movement, then test for smooth, quiet operation

This control switch regulates heat to a surface burner so the cooktop reaches and holds the selected temperature. Restores responsive burner control and consistent cooking performance. What it does:

• Sends variable power to a surface burner to adjust heat levels as you set the knob
• Commonly replaces a switch that causes a burner to stay cold, not heat, or only work at one setting
• Can fix clicking, intermittent operation, or loss of variable control on the affected element
• Works with the cooktop's control knob and wiring harness to manage element output

What's included:

• One replacement infinite burner control switch

Install notes:

• Disconnect power to the appliance before beginning any work
• Remove the cooktop or control panel as needed to access the switch; keep track of mounting hardware
• Match wire locations and connector orientation when reattaching harness; take a photo first if helpful

Microwave not heating but runs normally? A failed magnetron is the likely cause. This repair restores heating function. Moderate DIY difficulty.

The Door Switch is an OEM replacement part for Frigidaire wall ovens. It is a component located on the oven door that detects when the door is opened and closed. The door switch works alongside the control board to regulate oven operations based on door position.  

Symptoms of a bad door switch can include:

• Oven failing to automatically go into bake or warm modes after door closure
• Interior lights not turning on when the door is opened
• Control buttons/display remaining constantly lit instead of dimming
• Oven not heating or functioning properly in different modes

Causes relate to normal wear over extended use as the door switch mechanism cycles with frequent door openings and closings. Moisture exposure or impacts could also degrade switch performance.

This OEM Frigidaire switch is compatible with Amana, Jenn-Air, KitchenAid, and some Electrolux wall oven models as well.

Replacement power cord for your microwave. Connects the appliance to your electrical outlet. Order a new cord if yours is frayed, damaged, or missing.

This drive motor restores rotational power to the appliance's drum or agitator so loads spin and drain correctly. It's a direct-replacement motor designed to restore normal wash and spin cycles when the original motor fails. What it does:

• Provides the mechanical drive force for the washer drum/agitator so clothes tumble and spin
• Re-establishes proper agitation and spin speed control when a worn or failed motor causes no-spin or no-agitate symptoms
• Operates with the appliance's existing pulley, belt, or coupling
• Works as the core rotating component tied to load movement and draining functions

• One motor

• Disconnect power and water before beginning any repair; follow the appliance service manual for safe access
• Replacement typically requires removing cabinet panels, drive belt or coupling, and electrical connector—avoid forcing parts
• Inspect associated belts, couplings, and mounting hardware; replace worn items to prevent repeated failures

Restores interior and cooktop lighting in your microwave. Replace when bulb burns out or dims for clear visibility. Verify fit with your model number.

This is an electrical noise filter that suppresses electromagnetic interference generated by the microwave during operation. It prevents electrical noise from traveling back through the power line and affecting other electronics in your home. Replace this filter if the microwave trips breakers, causes interference with nearby devices, or fails to power on.

Fix a microwave that won't heat properly or shuts off early with a new temperature sensor. This part monitors internal temperature for safe operation.

Replace your microwave's mounting plate if it's cracked, bent, or missing. This structural component secures the microwave during installation.

This wiring diagram is the factory electrical schematic used to identify wire routing, connector locations, and circuit relationships—helpful for accurate diagnosis and repair planning. It provides a clear view of the appliance's electrical layout to guide troubleshooting. What it does:

• Shows wire colors, connector pinouts, and component wiring for the appliance circuitry
• Helps locate and identify wires and terminals when tracing electrical faults
• Assists technicians and DIYers in verifying proper connections during repairs
• Useful for diagnosing symptoms like no power to controls, intermittent operation, or blown fuses

• Always disconnect power to the appliance before inspecting or working on electrical components
• Use the diagram as a reference only; verify wire continuity and voltage with a multimeter before servicing
• Handle the diagram sheet carefully to avoid tearing or smudging; store with the appliance documentation

This is a black plastic lens and frame assembly that covers the interior lamp on a microwave oven. It protects the light bulb from grease and moisture while diffusing light inside the cooking cavity. Replace this lens if it is cracked, yellowed, melted, or missing, which can leave the bulb exposed to splatter and reduce interior illumination.

Mounting plate cover for your microwave. Installs on the support bracket assembly. Replace if cracked, broken, or missing to restore proper appearance.

Replacement cushion for your microwave door or cabinet. Installs to provide cushioning and prevent impact damage. Order a new cushion if worn or missing.

Controls airflow in your microwave's exhaust vent system. Installs between blower and duct. Replace if cracked, broken, sticking, or missing.

This is the roller guide assembly that sits on the floor of the microwave and supports the glass turntable tray, allowing it to rotate smoothly during cooking. It typically consists of a ring with small wheels or rollers. Replace this part if the turntable wobbles, does not rotate evenly, or if the rollers are broken or worn, which can cause uneven cooking or noise during operation.

Glass turntable tray for microwaves. Replaces cracked, broken, or missing rotating platters. Installs on turntable support to hold dishes during cooking.

This bushing guides and supports a rotating shaft to reduce wear and keep moving parts aligned, restoring smooth, quiet operation. Fits specific Frigidaire appliances—use the OEM part number to fit for your model. What it does

• Supports a rotating shaft or drum to prevent metal-on-metal contact
• Reduces friction and wear that can cause squeaks, grinding, or rough rotation
• Helps maintain proper alignment for consistent appliance performance
• Commonly replaces worn or damaged bushings that allow excessive play

• Disconnect power before servicing and access the affected assembly per your model's service manual
• Remove the worn bushing and any debris; press or tap the new bushing into place squarely
• Inspect mating shaft/surface for scoring or wear; replace or repair if damaged
• Use only OEM-recommended lubricants if specified by the manufacturer; do not assume grease is required

This is a plastic bracket that holds the door interlock switches in proper alignment inside the microwave's door latch assembly. It ensures the switches are correctly positioned to detect when the door is open or closed. Replace this part if the microwave won't start, runs with the door open, or if the switch holder is cracked or broken.

Secures your microwave to the wall or cabinet during installation. Replace this bracket if the original was lost, damaged, or missing during remodeling.

This small rubber bumper cushions and protects the appliance door and cabinet by absorbing impact and preventing metal-to-metal contact. It helps reduce door noise and wear for a quieter, smoother close. What it does:

• Acts as a door stop/cushion to prevent direct contact between the door and cabinet
• Reduces rattling, clanking, and vibration during door movement
• Helps maintain a proper door seal by stabilizing door position
• Commonly replaced when cracked, flattened, missing, or causing noise

• Usually installs by pressing into a pre-formed hole or onto a mounting peg; no special tools required
• Verify exact mounting location before removal; keep track of orientation for re-installation
• Disconnect power only if working near electrical components; this is typically a non-electrical part
• Inspect surrounding area for additional wear or missing fasteners while replacing

This is a translucent lens cover that sits over the interior or exterior light bulb in a microwave. It diffuses the light evenly and protects the bulb from grease and food splatter. Replace this lens if it is cracked, discolored, melted, or missing, which can leave the bulb exposed and reduce interior visibility.

Metal support bracket for microwave mounting and internal component stability. Replace if bent, cracked, or missing to restore proper structural support.

Replacement interior support plate for microwaves. Mounts inside the cavity to provide structural support. Order a new part if yours is cracked or broken.

This replacement duct guides internal airflow to and from the appliance, restoring proper ventilation and helping the unit maintain even temperatures. Designed to match the original fit and routing for reliable performance. What it does:

• Channels conditioned or exhaust air through the correct internal path
• Helps prevent airflow restrictions that can cause uneven cooling or heating
• Reduces rattling or vibration from a damaged or misrouted air path
• Supports normal compressor/fan operation by maintaining intended ventilation

• One replacement duct as shown

• Inspect surrounding connectors and seals; replace damaged gaskets for best results
• Secure all fasteners to prevent air leaks
• Disconnect power (and water if applicable) before beginning work to avoid injury
• Avoid sharp bends that can restrict airflow

This component supports the stirrer cover inside the microwave cavity, helping distribute microwave energy evenly. Replace it if the stirrer cover rattles, falls, or food heats unevenly.

Replacement turntable support for your microwave. Installs under the glass tray to allow smooth rotation. Replace if cracked, broken, or worn out.

Replacement turntable support for your microwave. Mounts under the glass tray to enable smooth rotation. Order a new support if yours is cracked or broken.

This replacement appliance label provides the factory identification and safety information fastened to the appliance so you can read model/serial and safety/warning text clearly. It restores legible markings for servicing and ownership records. What it does

• Shows the appliance identification, model/serial or rating area and factory safety/warning text so technicians and owners can service data.
• Helps ensure required safety and operating instructions remain visible and readable.
• Replaces a torn, faded, or missing label that can make identification and troubleshooting harder.
• Supports accurate parts ordering and service by restoring the original markings.

• One replacement label

• Peel-and-stick replacement; clean and dry the surface thoroughly before applying.
• Align carefully and press from one edge to the other to avoid bubbles; firm pressure ensures adhesion.
• Do not stretch or trim the label unless explicitly specified by the equipment instructions.
• For safety, disconnect power or follow manufacturer safety precautions before working near electrical components.

Charcoal air filter captures grease, smoke, and odors in over-the-range microwaves. Replace when performance declines. Confirm fit with your model number.

Grease filter for range hoods and over-the-range microwaves. Dimensions: 5-7/8" x 7-7/8" x 3/32" (5.875 x 7.875 x 0.09375). Rectangle shape. Captures grease from cooking air. Replace when clogged, discolored, or every 6-12 months.

Secures panels and components inside your microwave, keeping parts aligned and reducing rattles. Replace when clip is broken, cracked, or missing.

This is a replacement screw used to secure appliance components and panels so assemblies stay stable and aligned. It provides a straightforward fix when a mounting fastener is missing, stripped, or damaged. What it does

• Secures panels, brackets, or trim to prevent movement and vibration
• Stops rattling or loose parts caused by missing or damaged screws
• Restores proper fit and alignment of the affected assembly
• Works wherever the OEM-designated screw of this size and thread is required

• Turn power off or unplug the appliance before working on electrical areas
• Use the proper-size driver to avoid stripping the head
• Start threads by hand, then tighten until snug — do not overtighten
• If the original screw is corroded or the hole is damaged, inspect mating parts for repair before installing

This is a replacement screw used to secure appliance components and panels so assemblies stay stable and aligned. It provides a straightforward fix when a mounting fastener is missing, stripped, or damaged. What it does

• Secures panels, brackets, or trim to prevent movement and vibration
• Stops rattling or loose parts caused by missing or damaged screws
• Restores proper fit and alignment of the affected assembly
• Works wherever the OEM-designated screw of this size and thread is required

• Turn power off or unplug the appliance before working on electrical areas
• Use the proper-size driver to avoid stripping the head
• Start threads by hand, then tighten until snug — do not overtighten
• If the original screw is corroded or the hole is damaged, inspect mating parts for repair before installing

This is a replacement screw used to secure appliance components and panels so assemblies stay stable and aligned. It provides a straightforward fix when a mounting fastener is missing, stripped, or damaged. What it does

• Secures panels, brackets, or trim to prevent movement and vibration
• Stops rattling or loose parts caused by missing or damaged screws
• Restores proper fit and alignment of the affected assembly
• Works wherever the OEM-designated screw of this size and thread is required

• Turn power off or unplug the appliance before working on electrical areas
• Use the proper-size driver to avoid stripping the head
• Start threads by hand, then tighten until snug — do not overtighten
• If the original screw is corroded or the hole is damaged, inspect mating parts for repair before installing

Replacement screw fastener for microwaves. Secures panels, brackets, and trim pieces in place. Needed when original screws are stripped, lost, or missing.