Parts for Frigidaire FFC13C7AW3: 05 - Cabinet Parts

This temperature control knob replaces a worn or missing knob so you can easily adjust the cold-control setting. Restores smooth, precise temperature adjustments and a clean, factory look. What it does:

• Attaches to the cold-control (thermostat) shaft to change the temperature setting
• Provides secure grip and pointer alignment for accurate selections
• Typical failure symptoms: cracked or missing knob, stripped hub, or a knob that slips or won't turn the control

• 1 temperature control knob

• Disconnect power before servicing
• Pull the old knob straight off the shaft; avoid prying at an angle to prevent shaft damage
• Align the shaft shape with the new knob and press firmly until fully seated
• The pointer aligns with the control graphics after installation

This temperature control thermostat regulates cabinet temperature by cycling the cooling system on and off. It helps your appliance hold the setting you select so food stays cold without unnecessary overcooling.

• Senses internal temperature and opens/closes electrical contacts to start or stop the compressor
• Maintains the setpoint chosen with the control knob
• Symptoms of a failing control include: too warm or too cold temperatures
• Runs constantly or won't run unless tapped/adjusted
• Temperature knob has little or no effect on cooling

• Disconnect power before servicing
• Note wire locations and take photos before removal
• Route the sensing capillary/bulb exactly as original; do not kink or sharply bend it
• Secure the sensing bulb in its clips and ensure good contact; set to mid-range and allow up to 24 hours for temperatures to stabilize

This genuine appliance screw secures panels and components to keep your refrigerator parts aligned and stable. A small but essential fastener, it restores proper fit and stops rattling or loose trim for reliable operation. What it does:

• Fastens panels, trim, or internal components to the appliance frame
• Restores secure fit when factory screws are missing or stripped
• Stops vibration- or temperature-related rattling caused by loose hardware
• Helps maintain proper spacing and alignment of serviceable parts

• Turn off and unplug the appliance before servicing electrical or internal areas
• Use the matching screw hole and thread engagement; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking surrounding material

Color: white. Measures about 12 inches wide by 6 inches high by 23 inches deep.

The lower basket holds and organizes items in the bottom section of the freezer. Replace a bent, broken, or missing basket to restore tidy storage and easier access to food in the lower compartment.

• Provides stable, contained storage in the lower freezer area
• Replaces a damaged, bent, rusted, or missing lower basket
• Helps keep food visible and accessible, reducing clutter
• If the basket won't sit level or shows broken wires/coating, replacement is recommended

• Unplug the appliance before servicing
• Empty the compartment and lift out the old basket
• Set the new basket onto the lower supports and ensure it sits level and secure
• Reload items evenly to prevent tipping

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

This basket track replaces a worn or damaged guide that lets a freezer or refrigerator basket slide smoothly in and out. Restores stable movement and helps keep the basket aligned for reliable access. What it does:

• Provides a smooth sliding surface for a refrigerator/freezer basket or drawer
• Keeps the basket aligned to prevent tipping or binding during use
• Replaces cracked, bent or worn tracks that cause sticking or noisy operation
• Helps the basket seat securely to prevent items from shifting while opening

• Disconnect power to the appliance before starting any repair to reduce shock risk
• Remove the basket/drawer and fasteners to access the old track; keep hardware if reusing
• Align the replacement track and secure with the original screws; avoid over-tightening
• Test the basket movement after installation and recheck fasteners for a snug fit