Parts for Frigidaire FFSC2323LSDA: 04 - Cabinet Parts

Interior cover that shields the evaporator coil assembly and directs airflow. Replace if cracked, broken, or missing to protect internal components.

Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.

Genuine mounting screw secures panels, brackets, and covers inside your refrigerator. Replace missing, stripped, or corroded fasteners to restore secure fit.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.

Replacement door closer cam for refrigerator hinges. Installs on upper door hinge to control door swing and prevent cabinet damage. Needed when cracked or worn.

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

Lower door hinge bracket supports the bottom refrigerator door hinge assembly. Replace if bent, broken, or cracked to restore proper door alignment.

Lower door hinge secures the bottom corner of your refrigerator door and provides a pivot point for smooth opening and closing. Replace if cracked or worn.

Replacement corner trim that covers the cabinet edge of your refrigerator. Restores a finished look to cracked, chipped, or missing corner pieces.

OEM mounting bracket that secures the hinge and pin assembly inside your refrigerator. Replace if cracked, broken, or missing to restore proper alignment.

Supports and aligns the refrigerator door at the hinge pivot point. Replace if cracked, bent, or worn to restore stable door operation and proper sealing.

Covers and protects the upper door hinge area on your refrigerator. Replace this plastic cap if cracked, broken, or missing to restore a clean look.

Upper door hinge cover for side-by-side refrigerators. Conceals top hinge hardware for a clean finish. Replace if cracked, broken, or missing.

Specs: 1.40`` long

Specs: Hex head ,1/4-20 x 5/8

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Secures refrigerator shelves in their track for stable storage. Fits into shelf track to support glass or wire shelves. Replace if cracked or broken.

This main power control board is the appliance's central electronic module. It routes incoming power and coordinates key functions so the unit powers up, runs, and responds to controls as designed, restoring reliable operation when the original board fails. What it does:

• Distributes and regulates power to motors, valves, and other loads
• Processes inputs from sensors and user controls, switching relays/triacs accordingly
• Coordinates start-up and run cycles for consistent performance
• Typical symptoms include a dead/unresponsive unit, intermittent shutoffs, specific components not running, or visible heat damage on the board

• 1 main power control board

• Disconnect power before servicing; discharge any capacitors where applicable
• Use ESD protection and handle the board by the edges
• Photograph/label all connectors; transfer any jumpers or settings from the old board to the same positions if present
• Inspect wiring and connected components for shorts before restoring power

Refrigerator door guide channel that helps align and support the door mechanism. Replace if cracked, broken, or worn to restore proper door alignment.

Secures panels, brackets, handles, and trim inside your refrigerator. Replace missing, stripped, or damaged screws to eliminate rattling and looseness.

Lower kickplate grille that covers the toe-kick opening on your refrigerator. Replace when cracked, broken, or missing to restore appearance.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Supports refrigerator crisper or bin drawers for smooth gliding. Replace when drawers stick or bind. Confirm fit with your model number listed.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

This cover assembly replaces a damaged or missing cover on your appliance, protecting internal components and restoring a clean, finished appearance. Use it when the original is cracked, loose, or no longer secures properly.

• Shields internal parts from debris, spills, and accidental contact
• Helps keep components enclosed and aligned for reliable operation
• Restores the appliance's finished look after damage or wear
• Common signs of failure: cracks, broken or missing tabs, discoloration, rattling, or a cover that won't stay in place

• Disconnect power before servicing; shut off water supply if working near water connections
• Remove retaining screws or release tabs; note the orientation of the original cover
• Transfer and reuse original screws, clips, or seals if required
• Do not overtighten fasteners into plastic; ensure all tabs fully engage before testing

Seals evaporator cover to direct airflow and prevent frost buildup. Replace if worn, cracked, or causing excess frost. Confirm fit with your model number.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Light stays on or won't turn on when you open the fridge door? This door-activated switch controls interior lighting. Simple DIY fix for most models.

Supports the glass crisper cover in your refrigerator. Replace if cracked, broken, or missing. Installs on the refrigerator wall above the crisper drawer.

This return air seal keeps refrigerator airflow channels sealed so cold air returns to the evaporator properly, helping maintain consistent temperatures and reduce frost and moisture issues. It replaces a worn or damaged return-air gasket. What it does

• Seals the return-air opening to direct cold air back to the evaporator
• Helps maintain even cooling and prevents warm air infiltration
• Reduces frost, moisture buildup, and uneven temperature zones
• Commonly replaced when you notice poor cooling, excessive frost, or air leakage noises

• One return air seal

• Disconnect power before starting work
• Remove any trim or panels that block access to the return-air opening
• Seat the seal into the channel or mating surface; some installations use adhesive or retainers—follow the manufacturer's instructions

Refrigerator harness retaining clip secures wiring in place. Replace if broken or loose to prevent wire damage. Confirm fit with your model number.

Electrical wire harness for side-by-side refrigerators. Connects internal components. Replace if wires are frayed, connectors damaged, or broken.

Wiring harness for side-by-side refrigerators. Connects electrical components inside the unit. Replace if wires are frayed, damaged, or broken.

Touch-up paint for appliances to cover scratches, chips, and worn areas on exterior surfaces. Restores appearance of refrigerators, ranges, and more.

Plastic grommet that supports and secures refrigerator shelves. Replaces broken, cracked, or missing grommets causing shelves to lean or sag.

Color: White

This part number contains one (1) screw.

Rear support clip that holds the crisper cover shelf in place. Replace when broken, snapped, or cracked to restore stability to your crisper drawer area.