Parts for Frigidaire FFSC2323LSDA: 03 - Refrigerator Door Parts

This gray magnetic refrigerator door gasket replaces the perimeter seal on the fresh food door. It creates an airtight closure that keeps cold air in, blocks humid air, and helps prevent temperature swings, frost, and condensation. What it does:

• Seals the door perimeter with a flexible magnetic edge to stop air leaks
• Helps maintain proper refrigerator temperature and reduce frost/condensation near the door
• Restores smooth closing when the old gasket is torn, shrunken, or warped
• Typical symptoms: visible gaps, moisture on the gasket, frequent cycling, or food warming near the door

• 1 gray magnetic refrigerator door gasket

• Disconnect power before servicing
• Warm the new gasket with a hair dryer or hot water to relax folds for easier seating
• Remove the old gasket; press/fasten the new gasket evenly into the door channel or retainer, ensuring corners are fully engaged
• Close the door and check for uniform contact; adjust hinges or gently reshape with warm air as needed and allow the gasket to set with the door closed

The Can Rack is an OEM part for Frigidaire refrigerators. It provides shelving located internally for organized storage of canned drinks. The can rack creates additional capacity within the refrigerator compartment above other sliding shelves and drawers.

Causes of a bad can rack can include being damaged from accidental impacts if heavy items are dropped onto it from above over time.

Symptoms of a bad can rack include:

• Bent or misshapen wires that no longer securely hold cans
• Broken off sections that reduce usable shelf space
• Loose assembly unable to be positioned properly on refrigerator walls

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models. 

This dairy door is the flip-up cover for the refrigerator's dairy compartment on the fresh-food door. It keeps butter and cheese covered and contained, restoring a clean, finished look when the original cover is cracked or missing.

• Covers the dairy compartment and hinges open for easy access
• Helps keep small dairy items contained and organized on the door
• Replaces a cracked, warped, discolored, loose, or missing cover
• Closes properly when seated on the original hinge posts

• Disconnect power before servicing
• Remove the old cover by releasing its tabs from the hinge posts
• Align the new cover with the hinge posts and press to snap into place
• Avoid forcing brittle plastic; allow the part to reach room temperature before installation

This black door stop replaces the small bumper that limits a refrigerator/freezer door's travel, protecting the cabinet and hinge from damage. It restores proper door alignment and quiets contact when the door closes. What it does:

• Acts as a physical stop to prevent the door from swinging too far and hitting the cabinet
• Cushions door closure to reduce noise and wear on the hinge
• Helps maintain correct door alignment for a tight seal
• Common symptom: door scraping, slamming, or rubbing against cabinet edge

• Basic hand tools may be required; keep fasteners and mounting surfaces clean
• Turn off or unplug the appliance before performing any repairs that require moving the door
• Handle hardware carefully to avoid damaging surrounding trim or seals

This replacement screw secures appliance components to their mounting points so panels, brackets, and trim stay tight and aligned. Replace missing or stripped hardware to restore a solid, rattle-free fit and proper assembly integrity.

• Secures panels, brackets, and trim to prevent movement and maintain alignment
• Replaces missing, damaged, or stripped hardware that can compromise assembly
• Helps reduce rattling or vibration from loose components
• Restores proper fit after service or access panel removal

• Unplug the appliance before servicing; turn off water supply if working near dispenser/ice areas
• Compare the new screw to the original to ensure thread, head style, and length
• Start threading by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Retain and reuse any original washers, spacers, or clips as required

This #10-32 x 3/4-inch machine screw secures appliance components such as panels, brackets, and handles. Using the correct length and thread helps restore a snug, rattle-free hold wherever this screw is specified by the manufacturer.

• Fastens components with a #10-32 machine thread and 3/4-inch length
• Helps keep panels, trim, brackets, or handles secured and aligned
• Replaces missing, stripped, or corroded hardware
• Common signs include loose or wobbly parts, rattling, missing screws, or damaged screw heads/threads

• Disconnect power before servicing; if working near a water connection, shut off the water supply
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping plastic or threads
• Reuse any model-specific washers or spacers if present

This refrigerator dispenser bearing supports the auger shaft so it spins smoothly during ice dispensing. Replacing a worn bearing restores quieter, more reliable ice delivery and helps prevent binding or uneven crushing of cubes. What it does

• Supports and centers the ice auger/crusher shaft inside the ice bucket
• Reduces friction to allow smooth, consistent rotation
• Wear can cause grinding or squealing during dispensing
• Symptoms include slow/no ice dispensing, jamming, or intermittent operation

• 1 bearing

• Disconnect power and turn off the water supply before service
• Remove the ice bucket and disassemble the crusher housing to access the bearing
• Note the bearing's orientation; transfer any spacers or clips as found
• Reassemble carefully and ensure the auger turns freely by hand before restoring power

The Lower Door Closer is an OEM replacement part for Frigidaire refrigerators. It is a vital part that assists in securely shutting the refrigerator door. The door closer contains a calibrated spring mechanism designed to gently guide the door into the closed position without using forceful movements. 

Symptoms of a bad door closer include:

• The door not latching fully or popping back open easily  
• Difficulty closing the door all the way
• Excessive noise and banging when closing  
• Gaps appearing around the door seal

Causes can be regular wear and tear on the spring after prolonged use. Not allowing the door to fully close before reopening may also damage the door closer mechanism over time.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This door bin (also called a door shelf) mounts to the inner door panel and holds bottles, jars, and condiments. Replacing a cracked or missing bin restores storage capacity and keeps items upright when you open and close the door.

• Adds organized storage space on the door for frequently used items
• Attaches to molded rails/tabs to hold contents securely during door movement
• Replace if the bin is cracked, warped, or the retaining hooks are broken
• Common symptoms: bin falls off, won't stay in place, items slide out, or the bin is missing

• Unplug the appliance before servicing
• Lift the old bin straight up and out of the door-liner tabs; transfer contents
• Align the new bin with the same slots and press down firmly until fully seated
• Distribute weight evenly and avoid overloading after installation

The Door Bin is an OEM replacement part for Frigidaire refrigerators. Mounted on the fresh food compartment door, the white bin provides storage for snacks and beverages.

Causes of needing replacement include cracks or fractures over time from repeated loading/unloading of contents. Warping plastic that no longer securely clips into door rails is also remedied.

Symptoms of a failing bin consist of:

• Items freely sliding around uncontained during opening/closing of the door
• Difficulty completely emptying or accessing corners for cleaning
• Inability to re-secure basket into floor rails keeping it attached

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore ranges.

The Door Bin is an OEM replacement part specific to Frigidaire-brand refrigerator doors. As an interior storage component, the door bin provides convenient access to commonly used items. 

Symptoms of a damaged or worn door bin include:

• Warping, cracks, or splits develop in the plastic material
• Detached or loose hinges prevent secure attachment 
• Items inside shifting or falling out during opening/closing

Causes involve repeated opening/closing stresses over time weakening the plastic. Temperature fluctuations from door openings also affect integrity.

This genuine Frigidaire door bin is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.