Parts for Frigidaire FRSS2623AB2: Cabinet Parts

This plug covers the small factory test opening on an appliance cabinet or liner. Replacing a missing or damaged plug helps close the opening to maintain a better seal and restore a clean, finished appearance.

• Seals the factory test opening in the cabinet/panel
• Helps limit air and moisture infiltration through the hole
• Reduces condensation or frost forming around the opening
• Restores a finished look when the original cap is missing or damaged

• Disconnect power before servicing the appliance
• Clean and dry the opening area for proper fit
• Align and press the plug in by hand until it sits flush—do not force or enlarge the hole
• Avoid sharp tools or sealants that could damage the liner or insulation

This door light switch controls the refrigerator interior lamp, restoring reliable on/off operation for the cabinet light. It replaces a worn or broken switch to help ensure the light responds when the door opens and closes. What it does

• Opens and closes the circuit that powers the interior lamp when the door moves
• Replaces a faulty or loose switch that causes the light to stay on, not turn on, or work intermittently
• Mounts in the cabinet frame and is actuated by the door or a door cam
• Works with standard appliance wiring and lamp circuits

• One door light switch

• Disconnect power to the appliance before starting any work
• Access may require removing the light lens or inner cabinet trim; handle bulbs and lenses carefully
• Verify electrical connectors and switch orientation during reassembly

The Door Light Switch is an OEM part for Frigidaire refrigerators. It is a component located inside the refrigerator door that turns the interior light on and off based on door position. The light switch works with a door switch plate and light socket assembly to automatically illuminate the interior when the door is opened.

Causes of a bad switch can be normal wear and tear over time, especially from frequent door openings. The contact points within the switch can become corroded or damaged.

Symptoms of a bad light switch include:

• Interior light not turning on at all when door is opened
• Light remaining constantly on even when door is closed
• Inconsistent or intermittent lighting

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
 

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This door bushing kit replaces worn hinge bushings that keep refrigerator/freezer doors aligned for smooth, stable operation. Restores proper door rotation to reduce sagging, rubbing, and noisy or stiff hinges. What it does:

• Provides replacement hinge bushings that support the door on its hinge pin for correct alignment
• Helps stop door sag, scraping, and uneven gaps that let cold air escape
• Reduces hinge noise, sticking, and rough door movement
• Fits into the door hinge assembly to restore smooth pivoting action

• Always unplug the appliance or disconnect power before starting repairs
• Support the door while removing hinge pins to prevent dropping or damage
• Remove old bushings from the hinge housing and press or snap new bushings into place; reassemble hinge and confirm alignment

This hinge assembly replaces a worn or damaged refrigerator door hinge to secure and align the door for proper sealing and smooth opening. Fits factory mounting points for a direct replacement. What it does

• Supports and pivots the refrigerator door so it opens and closes correctly
• Restores proper door alignment to help improve the door seal and cooling consistency
• Stops sagging, rubbing, or uneven gaps that can cause drafts or noise
• Replaces broken or bent hinge hardware that prevents the door from seating

• One hinge assembly

• Unplug the appliance or disconnect power before beginning any repair
• Remove food and contents from the door and have a helper support the door during removal/installation
• Use basic hand tools; follow factory service instructions for torque and adjustment details

A direct-fit refrigerator door hinge assembly that restores proper door pivot and alignment for smooth opening and closing. Replaces a worn or damaged upper hinge to reduce sagging and keep the door sealed. What it does:

• Provides the pivot point for the refrigerator door and maintains proper alignment.
• Helps the door close fully to keep internal temperatures consistent.
• Commonly replaced when the door is sagging, hanging unevenly, or rubbing against the cabinet.
• Restores smooth, stable door movement and corrects uneven gaps.

• One hinge assembly.

• Unplug the appliance and empty or support the door before removing the hinge to prevent injury or damage.
• Keep door supported while swapping the hinge; some doors require two people or a support tool.
• Reuse any original mounting hardware unless replacements are explicitly provided.
• After installation, check door alignment and gasket seal; adjust as needed per the appliance manual.

This mounting bracket secures internal refrigerator components so panels, shelves or assemblies stay aligned and stable. Replaces a worn or broken bracket to reduce rattling and restore proper fit of affected parts. What it does:

• Provides a secure mounting point for panels, shelves or appliance assemblies
• Stops movement that can cause noise or misalignment
• Restores correct fit where a cracked or bent bracket allowed parts to sag
• Helps maintain safe, stable operation of the appliance

• Disconnect power before beginning any repair to reduce shock risk
• Basic hand tools are usually required; avoid overtightening fasteners
• Handle edges carefully to prevent cuts; wear gloves if needed

This mounting bracket secures internal components and panels to keep your appliance stable and aligned. It restores proper fit and reduces moving parts from shifting or vibrating during operation. What it does:

• Provides a stable anchor point for panels or internal assemblies to prevent sagging or misalignment
• Helps stop rattling, knocking, or vibration caused by loose fittings
• Maintains proper spacing so doors and service panels open and close smoothly
• Supports correct alignment of connected components for reliable operation

• One mounting bracket

• Disconnect power (unplug or shut off breaker) before starting any repair
• Installation typically requires basic hand tools (screwdriver, nut driver); keep original fasteners unless replacements are specified
• Align bracket, fasten securely, and test the appliance for proper fit and noise reduction

This replacement cover is a molded trim panel that protects and conceals internal components while restoring the appliance's finished appearance. It helps keep dirt and moisture away from sensitive parts for reliable, long-term operation. What it does:

• Covers and protects internal components from dust, spills, and everyday wear
• Restores the appliance's exterior appearance where the original cover was damaged or missing
• Helps maintain proper airflow paths and component placement when installed correctly
• Prevents accidental contact with electrical or mechanical parts behind the opening

• Disconnect power (unplug or shut off breaker) before beginning any repair.
• Handle the cover carefully to avoid scratches; use non-marring tools when prying or aligning.
• Follow the appliance manufacturer's instructions for fastening points and any required clips or screws.
• Reuse existing fasteners or order OEM hardware separately.

Specs: .875`` long

Specs: 1.40`` long

Specs: Hex head ,1/4-20 x 5/8

The Roller Assembly is an OEM part for Frigidaire refrigerators. It is responsible for allowing movement and stability of the refrigerator cabinet. 

A bad refrigerator wheel can be caused by wear and tear, damage, or excessive weight on the appliance. When the wheel becomes faulty, it can result in issues such as difficulty in moving or repositioning the refrigerator, uneven or wobbly movement, or scratching of the flooring.

Symptoms of a bad roller assembly include:

• Difficulty in moving the refrigerator
• Uneven movement when moving the appliance
• Scratching or scuffing of the flooring 

Replace your faulty cabinet roller assembly with this genuine OEM part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This replacement screw fastens appliance components such as panels, brackets, and covers. Installing a new fastener restores a snug, rattle-free fit when the original screw is missing, stripped, or corroded.

• Secures covers, brackets, or trim to the cabinet or liner
• Replaces missing, stripped, or rusted hardware
• Helps reduce vibration and rattling from loose parts
• Supports proper alignment and stability of assemblies

• Disconnect power before servicing the appliance
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal
• Retain and reinstall any original washers or spacers, if present

The Main Control Board is an OEM replacement part for Frigidaire refrigerators. It is an electronic component that controls various refrigerator functions such as temperature settings, cycles, diagnostics, and more. 

Symptoms of a bad PC board include:

• Refrigerator not cooling or icing 
• Display or control panel not working properly
• Inability to change temperature settings
• Abnormal or unexpected clicking/humming sounds

Causes of failure could include exposure to moisture, power surges, or general component fatigue over time. 

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This factory screw fastens refrigerator components and panels. It replaces missing or damaged hardware so parts stay aligned and secure, reducing looseness and rattles caused by vibration. What it does:

• Secures panels, brackets, and trim per your model's design
• Helps maintain alignment and reduce vibration-related loosening or noise
• Replaces missing, stripped, or corroded hardware
• Restores a snug fit when threads or heads are worn

• One screw

• Disconnect power; turn off the water supply if working near ice or dispenser systems
• Use the correct driver; start threading by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking adjacent plastic
• Refer to your model's diagram to confirm location and quantity used

This genuine replacement screw secures appliance components and panels so parts stay properly aligned and rattle-free. Use it to replace a missing, stripped, or corroded fastener and restore a snug, reliable fit.

• Fastens brackets, covers, panels, and other hardware in their original locations
• Helps resolve loose or vibrating components and rattling noises
• Replaces missing or damaged hardware that can cause gaps or misalignment
• May be used in multiple locations

• Disconnect power; shut off water supply if working near water lines
• Compare to the original screw and install in the same location/orientation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Refer to your model's exploded view to verify quantity and placement

The Grille/kickplate is an OEM replacement part for Frigidaire refrigerators. It sits at the base of the refrigerator, covering the vents and providing a finished look. The grille/kickplate regulates air flow from the vents and directs it appropriately within the refrigerator compartment.

Causes of a bad grille/kickplate can include damage or cracks that impair its function, or wear and tear over time that degrades its fit and finish. 

Symptoms of a bad grille/kickplate include:

• Excessive dust buildup inside the refrigerator 
• Unbalanced or uneven air flow causing temperature fluctuations
• Cool air leaking out of the bottom vents
• The grille no longer fitting securely in place

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This drawer roller allows your refrigerator's bin or crisper drawer to glide smoothly along its track. Replacing a worn or missing roller helps restore easy opening and closing and prevents drawers from sticking or binding.

• Supports the drawer as it slides on the rail/track
• Helps correct stiff, rough, or noisy drawer movement
• Can reduce uneven sliding or a drawer that pops off the track
• Common wear item when drawers are overloaded or used heavily

• Unplug the refrigerator before servicing
• Remove the affected drawer to access the roller
• Note roller orientation and reuse existing fasteners if applicable
• Test drawer travel after replacement to ensure smooth operation

This rivet is a metal fastener used to permanently secure panels, brackets, or internal components in your appliance. Replacing a damaged or missing rivet restores a tight fit and helps prevent vibration, rattles, and looseness.

• Permanently joins thin metal parts where screws or nuts aren't used
• Maintains alignment and structural integrity of housings and frames
• Helpful when panels or components are loose, rattling, or won't stay secured
• Direct replacement for a worn, broken, corroded, or drilled-out factory rivet

• Disconnect power and shut off gas/water (as applicable) before servicing
• Support the part being fastened; drill out the old rivet head if needed
• A hand riveter/rivet tool may be required to set the new rivet
• Wear eye and hand protection during drilling/riveting

This hex head screw secures panels, brackets, and small components on appliances, restoring proper fit and stability. It's a direct replacement fastener when an original mounting screw is missing, loose, or damaged. What it does:

• Secures panels, brackets, trim, and internal components to prevent rattling or movement
• Replaces stripped, missing, or damaged mounting screws that cause loose parts or misalignment
• Restores reliable mechanical fastening so doors and panels sit flush and operate correctly
• Works as a general-purpose appliance mounting screw when original fasteners are worn

• Always disconnect power to the appliance before starting any repair
• Match the screw to the original location and thread engagement; start by hand to avoid cross-threading
• Use the correct driver or socket for the hex head and tighten until snug—do not overtighten
• If the original hole or threads are damaged, repair or replace the mating hardware before installing the screw

This cover assembly replaces a damaged or missing cover on your appliance, protecting internal components and restoring a clean, finished appearance. Use it when the original is cracked, loose, or no longer secures properly.

• Shields internal parts from debris, spills, and accidental contact
• Helps keep components enclosed and aligned for reliable operation
• Restores the appliance's finished look after damage or wear
• Common signs of failure: cracks, broken or missing tabs, discoloration, rattling, or a cover that won't stay in place

• Disconnect power before servicing; shut off water supply if working near water connections
• Remove retaining screws or release tabs; note the orientation of the original cover
• Transfer and reuse original screws, clips, or seals if required
• Do not overtighten fasteners into plastic; ensure all tabs fully engage before testing

This coil cover seal is a molded gasket that fits around the evaporator/coil cover to help keep airflow directed and reduce moisture and frost buildup. It restores the cover's sealing surface for more consistent cooling performance. What it does:

• Seals the evaporator/coil cover to help maintain proper airflow through the coil
• Helps reduce frost or ice buildup by keeping moist air away from cold coil surfaces
• Can prevent water dripping or pooling inside the cabinet near the coil
• Restores a tighter seal after a cracked, torn, or compressed gasket reduces effectiveness

• Disconnect power to the appliance before starting any repair
• You may need to remove the evaporator/coil cover or access panel to reach the seal
• Clean the mating surfaces and dry thoroughly before installing the new seal
• Handle the gasket gently and press evenly to seat; avoid stretching or sharp tools that could damage the part

The Ice Maker Cooling Duct is an OEM part for Frigidaire refrigerators. It directs cold air flow to the ice maker.

Causes of failure can be blockages or damage to the duct over time that impact efficient air flow.

Symptoms of a bad cooling duct include:

• Inconsistently shaped or formed ice cubes
• Slow or reduced ice production
• The ice maker failing to dispense ice properly
• Higher than normal interior refrigerator temperatures near the ice maker

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models. 

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This is a replacement outer housing cover that restores the appliance's exterior protection and appearance. It shields internal components from debris and helps maintain a finished look for the unit. What it does:

• Covers and protects internal components from dust, dirt and incidental contact
• Restores a clean, finished exterior where the original cover was cracked, warped or missing
• Helps prevent small objects from falling into internal openings
• Reduces visible wear on the appliance for a neater installation

• Disconnect power to the appliance before starting any work
• Remove any retaining screws or clips holding the old cover in place; lift or slide out gently
• Align the replacement cover carefully and re-secure with original hardware

The Thermistor is an OEM part for Frigidaire refrigerators and freezers, designed to accurately monitor and control the temperature within the appliance. This sensitive component reacts to temperature changes by altering its resistance, providing feedback to the control board to regulate the cooling and defrost cycles.  

Causes of thermistor failure can include physical damage, electrical failures within the circuit, or aging, which affects its accuracy and responsiveness.

Symptoms of a bad Thermistor include:

• Unusual temperature fluctuations in the refrigerator or freezer
• The appliance is constantly running or not cooling efficiently
• Error codes displayed on the refrigerator's control panel indicating thermistor problems
• Buildup of frost in the freezer or condensation in the fridge

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This support is the structural piece that holds and aligns a shelf, rack, or panel within your appliance. Replacing a worn or broken support restores proper fit and stability to prevent wobble, sagging, and related damage. What it does:

• Provides stable mounting and positioning for the associated shelf, rack, or component
• Helps maintain alignment so parts sit or slide correctly
• Replace if cracked, deformed, loose, or missing
• Symptoms can include a component that sits unevenly, drops, or won't stay in place

• Includes 1 support

• Disconnect power to the appliance before servicing
• Allow any hot surfaces to cool; wear cut-resistant gloves
• Note the orientation of the original part; reuse existing fasteners if applicable
• Ensure the support is fully seated and secure before returning the appliance to use