Parts for Frigidaire LCE752LL2: 05 - Cabinet Parts

Door hinge bar kit for washer dryer combo units. Replaces broken, worn, or damaged hinge bars that prevent proper door alignment and operation.

The hinge grommet provides cushioning and smooth operation where the washer lid connects to the main body. Replace if the lid doesn't close properly, makes grinding noises when opening/closing, or appears loose and wobbly.

Washer won't start or advance to spin cycle? A broken lid strike prevents the lock from engaging. Simple 5-minute snap-in fix—just remove two screws.

Secures the door strike to your washer, keeping the latch aligned for firm closure. Replace if missing, stripped, or corroded to restore reliable latching.

Rubber bumper cushions washer lid closure. Installs between lid and cabinet to absorb impact and reduce noise. Replace if worn, cracked, or missing.

Replacement pin for washer components. Secures and connects internal parts. Needed when original pin is broken, missing, or worn from use.

This water inlet valve controls water flow to the refrigerator's dispenser and ice maker, restoring proper water supply when the valve fails. Direct-fit replacement that helps stop leaks, no water flow, or intermittent dispensing. What it does:

• Opens and closes to allow water into the ice maker and/or door dispenser when requested
• Stops water flow when idle to prevent leaks and overfilling
• Common repair for no water, slow fill, or continuous dripping from dispenser or ice maker
• Electromechanical valve driven by refrigerator control signals

• Disconnect power and shut off the household water supply before starting
• Replace only with parts specified for your model;
• Inspect and tighten or replace inlet hoses and clamps if corroded or damaged

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

This part has been discontinued by the manufacturer and is no longer available.

Washer won't fill with water or only fills with hot? The water inlet valve controls water flow into the tub. DIY repair takes about 30 minutes.

Shipping block for washers, installs inside cabinet to secure the tub during transport or moving. Replace if lost, broken, or missing from original packaging.

This is a small rubber or plastic cup that sits beneath a washer's leveling leg to protect the floor and reduce vibration. It helps keep the machine stable and prevents the legs from scratching or damaging the surface underneath. Replace this pad if it is cracked, compressed, or missing, which can cause the washer to vibrate excessively, walk across the floor, or make loud banging noises during the spin cycle.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This washer switch is both the lid lock and lid switch. New mounting bracket replaces older design. Which means in some applications you may need to drill off old design mounting bracket prior to mounting the new lock. If your replacing the 4 wire switch you will need to tape off light switch leads. The light will no longer be used. Instructions included.

This washer switch is both the lid lock and lid switch. New mounting bracket replaces older design. Which means in some applications you may need to drill off old design mounting bracket prior to mounting the new lock. If your replacing the 4 wire switch you will need to tape off light switch leads. The light will no longer be used. Instructions included.

This is a small spring that attaches to the lid of a laundry center washer, providing tension to hold the lid in position. It helps the lid stay open during loading and close securely during operation. Replace this spring if your washer lid won't stay open, slams shut on its own, or the original spring is broken or stretched out.

This is a small rubber or plastic cup that sits beneath a washer's leveling leg to protect the floor and reduce vibration. It helps keep the machine stable and prevents the legs from scratching or damaging the surface underneath. Replace this pad if it is cracked, compressed, or missing, which can cause the washer to vibrate excessively, walk across the floor, or make loud banging noises during the spin cycle.

This component adjusts the tension of washer suspension springs in laundry center units and is located within the suspension system. Replace when experiencing excessive vibration, unbalanced loads, or unusual movement during spin cycles.

Snap-in bushing for washer assemblies. Replaces worn, cracked, or missing bushings that provide cushioning and support in internal components.

Hex flange nut with 10-32 thread secures components in appliances. Replace if stripped, missing, or damaged. Flange provides broader bearing surface.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.