Parts for Ge GFDS355EL1MV: 04 - Cabinet & Top Panel Parts

Wire harness for dishwashers. Replaces damaged, frayed, or burnt wiring connections inside your appliance. Essential when harness is broken or worn.

This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.

• Fastens parts where a #10-16 x 1/2-inch hex washer-head screw is specified
• Secures brackets, panels, and assemblies to the tub or frame
• Helps resolve symptoms like loose panels, vibration, or rattling noises
• Restores proper hold when the original screw is stripped, missing, or damaged

• Disconnect power and shut off water to the dishwasher before servicing
• Match length and thread to the original; replace screws one at a time to maintain alignment
• Start threading by hand to avoid cross-threading; tighten snugly—do not overtighten, especially into plastic
• Verify no wires or hoses are pinched before reassembly

• Size: #10-16 x 1/2 inch
• Head: hex washer-head
• Type: AB tapping screw

Mounting screw for dryer drum support and internal components. Replaces lost, stripped, or damaged screws during repairs. Package of 12 screws included.

This adjustable gray foot supports and levels your dryer, allowing you to compensate for uneven floors. It screws into the dryer's base and can be raised or lowered to ensure the appliance sits level and stable. Replace this part if your dryer rocks, vibrates excessively, or appears tilted.

Replacement bottom chassis base for your dryer. Supports and stabilizes the drum and internal components. Needed when original is cracked or damaged.

Replaces the rear mounting bracket that secures a leveling leg to your dryer frame. Needed when the original bracket is cracked, broken, or missing.

Rear bracket and leveling screw assembly.

Dryer won't start or keeps tripping the breaker? A damaged terminal block disrupts power distribution. DIY repair typically takes 30-45 minutes.

Protective cover that shields the rear power connection terminals on your dryer. Replace if cracked, broken, or missing to prevent lint buildup and accidental contact with electrical connections.

Replacement strain relief bracket that secures the power cord at entry point. Needed when bracket is cracked, broken, or missing to restore safe cord routing.

Size: 8-32 t. Includes 12 screws.

The Water Valve is an OEM part for GE electric dryers. Located near the bottom of the machine, it controls water flow into the condenser system during moisture-sensing cycles.

The moisture sensing function uses this valve to introduce precise amounts of water vapor into the exhaust air stream periodically. This allows the condenser to capture moisture readings accurately and determine optimal cycle time based on humidity levels. 

Causes of failure include mineral buildup restricting flow, worn seals enabling leaks, or misaligned internal components hindering valve movement.

Symptoms of a faulty water valve are: 

• Loss of moisture sensing ability
• Incomplete or improper readings affecting cycle times  
• Water leaks from the valve area
• Failure to inject water vapor as needed

This part is also compatible with some Kenmore models using GE components.

Includes 12 screws. Size: 8-18 ab.

Fix a dryer that won't turn on or power up. This main power control board restores electrical functions. Moderate DIY repair for experienced users.

Mounting bracket that secures your dryer's main control board in place. Replace if cracked, bent, or broken to prevent board movement and maintain stability.

Replace missing or stripped screws that secure dryer components. This fastener installs in various internal locations to hold panels and parts in place.

Replacement screw for securing dryer components like drum supports, panels, and housings. Needed when screws are lost, stripped, or damaged during repair.

Replacement mounting screw for dryer panels, brackets, and components. Needed when screws are missing, stripped, or damaged during repairs or disassembly.

10-16 x 1-1/4 inch screw for securing dryer panels, brackets, and internal components. Replace missing, stripped, or damaged screws during repairs.

Mounting screw for dryer assembly. Secures panels, brackets, or internal components. Replace if stripped, missing, or damaged during repairs.