Parts for Ge PFQ97HSPV1DS: Cabinet & Top Panel Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Replacement wire tie for your washer. Secures wiring harnesses and hoses inside the cabinet. Order a new tie if yours is broken, missing, or damaged.

This power cord fix belt is a small cord-retaining strap that secures the appliance power cord to the cabinet. It helps keep the cord in place to reduce strain on the cord connection and maintain a reliable power connection. What it does:

• Holds the power cord firmly against the appliance frame to prevent tugging on the wiring
• Reduces movement that can loosen or wear the cord connection over time
• Helps prevent intermittent power or connection issues caused by a shifted cord
• Keeps cord routing neat and reduces stress at the plug/body interface

• One power cord fix belt

• Always disconnect power before accessing the cord or electrical panels
• Typically installs behind a rear access panel or at the cord entry point; basic tools may be required
• Position so the cord is secure but not pinched; replace if cracked or brittle

This electronic main control board manages oven functions and user interface, restoring reliable cycle control and feature operation. Replace a failed board to regain normal oven control and display responsiveness. What it does:

• Controls oven heating cycles, temperature commands and timed functions
• Interfaces with the front control panel and sensors to execute user inputs
• Helps resolve symptoms like unresponsive controls, incorrect cycle behavior, or no display/erratic operation
• Works as the central processor for coordinated oven component control

• Disconnect power at the breaker before accessing or replacing the control board
• Handle the board by its edges and avoid touching components or connectors to prevent damage from static
• Verify connector locations and secure all wiring harnesses before restoring power

Washer not filling properly or overfilling? This water level sensor detects tub levels and signals when to stop filling. Moderate DIY repair.

This main wiring harness assembly routes power and signals between the control, motor, door switch and other dryer components to restore proper electrical connections and enable normal operation. What it does

• Replaces the dryer's primary wire harness that supplies power and control signals to internal components
• Restores connection to the control console, motor, door switch and safety interlocks
• Can resolve symptoms such as no power to the drum or controls, intermittent electrical failures, or a dryer that won't start
• Helps correct issues caused by damaged, burned, or disconnected wiring and connectors

• One main wiring harness assembly as shown

• Disconnect all power (unplug or switch off breaker) before starting work
• Take photos of original routing and connector positions to aid reassembly
• Route harness to avoid pinch points or contact with sharp edges and secure with existing clips/fasteners
• Reconnect all matching plugs fully; test operation after reassembly

Support bracket for washer external drain hose. Secures and stabilizes the drain hose connection. Replace if cracked, broken, or missing.

Guides and secures the external drain hose on your washer. Replace if cracked, broken, or missing to ensure proper hose positioning during drainage.

Internal support bracket for washer external drain hose. Secures and stabilizes the drain hose connection. Replace if cracked, broken, or missing.

Fix water leaks or pooling inside your washer with this drain hose clamp. Secures the internal drain hose to prevent water buildup. Simple DIY repair.

Replace a missing or corroded ground screw to restore proper electrical grounding. Prevents shock hazards and ensures safe appliance operation. Quick fix.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Fix excessive shaking and loud banging during spin cycles with this washer damper pin. Simple DIY repair using basic tools like pliers and a screwdriver.

This top panel pin secures the appliance's top panel to the cabinet, keeping the panel aligned and stable for safe use. Replaces a worn or broken pin to stop panel movement and rattling. What it does:

• Holds the top panel in place so it stays aligned with the cabinet
• Prevents the panel from shifting, rattling, or lifting during use
• Restores a secure fit after a bent, broken, or missing pin
• Simple, single-piece replacement used where the panel pivots or seats

• One top panel pin

• Turn power off and unplug the appliance before beginning any work
• Remove the top panel per the manufacturer's instructions to access the pin
• Inspect surrounding clips and brackets; replace damaged hardware as needed

This rear damper bracket secures the refrigerator damper assembly to the cabinet, keeping the air-flow control components aligned for proper operation. Replacing a broken bracket restores stable damper positioning and helps reduce noise and airflow issues. What it does:

• Holds the damper assembly in place at the back of the cabinet so the damper can open and close correctly
• Prevents the damper from shifting or rattling, which can cause unusual noises
• Helps maintain consistent airflow from the freezer/fridge duct by keeping the damper aligned
• Useful when the original bracket is cracked, broken, or missing mounting points

• One rear damper bracket

• Disconnect power to the appliance before starting any repair
• Remove any interior shelving or rear access panels necessary to reach the damper area
• Keep fasteners and any small clips; transfer them only if compatible and explicitly required
• Inspect the damper and actuator for wear before reassembly

This front damper bracket secures the refrigerator air-damper assembly to the cabinet, helping maintain proper airflow between compartments for consistent cooling. Durable replacement part designed to restore damper alignment and function. What it does

• Holds the air-damper assembly in the correct position to regulate cold-air flow between freezer and fresh-food sections.
• Helps prevent damper misalignment that can cause uneven temperatures or airflow noise.
• Works with the damper actuator and housing to enable controlled opening and closing of the air passage.
• Common symptom: broken, loose, or cracked bracket causing a rattling sound or improper damper movement.

• One front damper bracket.

• Intended for use in refrigerators; follow manufacturer service instructions for access and removal of interior panels.
• Disconnect power (unplug or shut off breaker) before starting any repair to avoid electrical shock.
• Use basic hand tools; avoid overtightening fasteners to prevent cracking the new bracket.

Adjustable leveling leg for front-load washers. Provides stable support and proper leveling. Replace if broken, cracked, or worn to restore balance.

Long shipping bolt that secures washer internal parts during transport. Replace when original bolt is missing, bent, or stripped for stable moves.

Secures internal assemblies during washer transport. Replace if lost, stripped, or damaged during installation or moving. Essential for safe relocation.

Plugs the opening left by a shipping bolt on your washer. Covers the unused fastener hole to keep out dust and debris while restoring a clean look.

External drain hose support bracket for front-load washers. Secures the drain hose in proper position. Replace if cracked, broken, or missing.

Secures the drain hose to your washer's pump or outlet. Replace this screw if it's stripped, missing, or damaged, causing the hose to loosen or detach.

Stabilizes washer internal components during transport. Install before moving to prevent damage from vibration and shifting. Replaces broken or missing brackets.

Secure clamp for washer tub vent hose. Replace if loose, cracked, or leaking to prevent water damage. Verify fit with your model number.

This is a ST3.5 x 12 self-tapping screw designed to secure trim, panels, and small appliance components. It replaces stripped or missing screws to restore proper fit and reduce movement or vibration. What it does:

• Fastens appliance panels, brackets, or trim where ST3.5 x 12 screws are specified
• Helps stop rattling, loose panels, or parts that shift during operation
• Provides a secure threaded hold in thin sheet metal or plastic mounting points
• Matches OEM fit where the WH02X26267 screw is specified

• Use the properly sized Phillips driver to avoid cam-out and head damage
• Start screws straight and apply steady pressure; do not over-torque to prevent stripping
• Wear eye protection when working with small fasteners and sharp edges
• Compare size and thread to ensure a proper match

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.