Parts for Ge PFQ97HSPV1DS: Controls & Dispenser Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This power cord fix belt is a small cord-retaining strap that secures the appliance power cord to the cabinet. It helps keep the cord in place to reduce strain on the cord connection and maintain a reliable power connection. What it does:

• Holds the power cord firmly against the appliance frame to prevent tugging on the wiring
• Reduces movement that can loosen or wear the cord connection over time
• Helps prevent intermittent power or connection issues caused by a shifted cord
• Keeps cord routing neat and reduces stress at the plug/body interface

• One power cord fix belt

• Always disconnect power before accessing the cord or electrical panels
• Typically installs behind a rear access panel or at the cord entry point; basic tools may be required
• Position so the cord is secure but not pinched; replace if cracked or brittle

This out-of-balance micro switch is the load-sensing switch that tells the washer when a tub is unbalanced so the control can pause or redistribute the load, helping prevent excessive vibration and damage during spin cycles. What it does:

• Detects excessive tub movement or imbalance and signals the washer control to stop or adjust the spin cycle
• Helps prevent noisy, vibrating, or shifting loads from continuing to spin
• Can cause the washer to stop mid-cycle or fail to enter high-speed spin when faulty
• Works as the electrical contact that completes or interrupts the control circuit based on tub position

• Disconnect power (and water if required) before beginning service
• Access usually requires removing the top or console and inner control/sensor cover—follow your model's service instructions
• Replace the switch with the identical part and reconnect wiring harnesses to matching terminals
• Test the washer through a diagnostic or a short cycle to ensure proper operation after installation

Replacement screw set for securing the front panel to your dryer or washer chassis. Install when original screws are stripped, missing, or damaged.

This lint filter handle seal strip replaces the worn or damaged rubber seal on a dryer lint screen handle to restore a snug fit and help keep lint contained. Replacing a split or missing seal improves seal contact and reduces lint escape. What it does:

• Provides a flexible rubber seal that fits over the lint filter handle edge to create a tighter contact with the dryer opening.
• Helps prevent lint and debris from bypassing the lint screen and collecting inside the dryer cabinet.
• Reduces gaps that can allow air leakage, which may affect dryer performance.
• Useful when the original seal is torn, hardened, missing, or no longer grips the handle securely.

• One lint filter handle seal strip (single piece as shown)

• Disconnect power to the dryer before service to avoid shock or injury.
• Remove the lint screen and peel off the old seal; clean the handle area before installing the new strip.
• Press the new seal strip firmly into place along the handle edge so it seats evenly; trim excess only if explicitly required by the OEM.

Prevents water backflow and siphoning in your laundry center. This inline check valve stops reverse flow to protect drain and water systems. Easy install.

This handle attaches to the refrigerator's internal water filter housing to secure and release the replaceable cartridge, making filter changes quick and reliable. Replaces a damaged or broken filter handle to restore proper filter removal and installation. What it does:

• Secures the water filter cartridge in the housing so it stays seated during normal use
• Provides a release point to remove the filter for replacement
• Stops leaks or loose fit caused by a cracked or broken handle
• Helps restore proper filter alignment and user access

• One filter handle

• Turn off the water supply to the refrigerator before servicing the filter assembly
• Remove the old handle by following OEM release instructions; replace with the new handle and confirm proper engagement
• No special tools typically required; use caution to avoid damaging the filter housing or surrounding trim

This electromagnetic valve (solenoid) controls water flow in compatible appliances, restoring proper fill and shutoff where the valve has failed. It provides a direct replacement to help resolve water delivery issues safely and reliably. What it does:

• Opens and closes to control water flow to icemakers, dispensers or fill circuits when energized
• Stops water flow to prevent overfilling when functioning correctly
• Commonly replaces valves that cause no water to dispense, intermittent filling, or slow/weak fills
• Acts as a sealed, electrically operated on/off valve in the appliance's water system

• Disconnect power and shut off the water supply before beginning any repair
• Handle and install the valve by the body; avoid stressing electrical connectors or inlet/outlet fittings
• Inspect hoses and fittings for damage; replace worn seals to prevent leaks
• Follow the appliance manufacturer's instructions and torque recommendations for proper installation

This water inlet tube clamp secures the refrigerator/ice maker water inlet tube to the housing, helping prevent leaks and tube movement. Designed to keep the fill line stable for reliable water and ice delivery. What it does:

• Holds the water inlet tube in place to reduce stress and movement at the connection
• Helps prevent chafing or kinking that can lead to leaks or flow restriction
• Maintains proper alignment of the fill line during normal use and servicing
• Fits where the inlet tube passes through or attaches to the fridge housing

• Turn off power and water supply before servicing the appliance
• Accessible from inside the refrigerator or behind the toe grille depending on model; remove panels as needed
• Inspect tubing and fittings; replace clamp only if it matches OEM fit and function

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Fix water leaks or pooling inside your washer with this drain hose clamp. Secures the internal drain hose to prevent water buildup. Simple DIY repair.

If your washer dispenser isn't filling properly or water flow is weak, this fill hose nozzle directs water into the dispenser assembly correctly.

Secures the power cord strain relief to your dryer chassis. Replaces lost or damaged mounting screws to restore secure cord attachment and reduce stress.

Fix washer door won't latch or lock errors with this door strike screw. Secures the strike to your washer door for reliable closure. Simple fix.

These mounting screws secure the refrigerator water inlet valve to the appliance frame, keeping the valve and water line stable during normal use. Replacing worn or missing screws restores proper valve alignment and reduces vibration. What it does:

• Fastens the water inlet valve to the cabinet or bracket so the valve stays in place
• Prevents valve movement that can stress supply lines or cause noise during fill cycles
• Helps maintain a consistent seal at the valve connection to reduce risk of leaks
• Restores factory mounting hardware fit after loss or corrosion

• Disconnect power to the appliance and shut off the water supply before installing
• Use the correct screwdriver or driver bit to avoid stripping heads
• Replace only with the exact screw size and type for proper fit; do not over-tighten
• Inspect surrounding valve and tubing for damage while mounting; tighten connections to manufacturer torque recommendations

Directs water from inlet to washer tub with secure clamp connection. Replace if cracked, worn, or leaking to restore proper water flow. Confirm fit.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.