Parts for Ge GFD48GSPK0RR: Cabinet & Top Panel Parts

This leveling leg threads into the base of your laundry appliance to set height and keep the cabinet stable. Replacing a worn, cracked, or missing leg helps stop rocking and vibration for smoother, quieter operation.

• Adjusts to level the unit on uneven floors
• Supports the cabinet and helps prevent walking or rattling
• Reduces noise and vibration from an unsteady base
• Replace when threads are stripped or the foot is damaged

• Disconnect power; shut off gas supply
• With a helper, carefully tip and support the unit; protect floors
• Thread the new leg by hand to avoid cross-threading, then fine-adjust with a wrench
• Level front-to-back and side-to-side; ensure all feet contact the floor; tighten any lock nut if present

Size: 8-18 b.

This hex-head screw secures dishwasher panels, brackets, and internal hardware so parts stay tight and rattle-free. Replace missing or stripped fasteners to restore a secure fit and reliable operation.

• Fastens panels, brackets, and other dishwasher components to the tub or frame
• Replaces a missing, stripped, or corroded screw that no longer holds securely
• Helps eliminate vibration and rattling caused by loose hardware
• Maintains proper alignment and secure mounting of parts during operation

• Disconnect power and shut off water supply before servicing
• Keep track of fastener locations and orientation for correct reassembly
• Start threads by hand; use an appropriate nut driver or socket to tighten
• Tighten snugly—do not overtighten, especially when threading into plastic

Size: 8 - 18 ab.

This top panel bushing cushions and secures the appliance top panel, helping reduce vibration and wear where the panel mounts. It restores proper fit and quieter operation when the top panel is loose or squeaks. What it does:

• Acts as a mounting insulator between the top panel and cabinet to prevent metal-on-metal contact
• Reduces rattling, vibration and squeaking caused by worn or missing bushings
• Helps maintain correct alignment of the top panel for a snug fit
• Prevents premature damage to the panel mounting points from movement

• Disconnect power to the appliance before starting any repair
• Remove the top panel or access panel per the appliance's service instructions to reach the bushing
• Press the old bushing out and install the new bushing fully into the mounting hole; verify panel alignment before reassembly
• Wear gloves and eye protection; inspect adjacent mounting clips or hardware and replace if damaged

This Shield Water Valve controls water flow to the appliance's dispenser and ice-making system, restoring proper filling and reducing leaks when the valve assembly is failing. Direct-fit replacement for the original inlet valve assembly. What it does:

• Opens and closes the water supply to the dispenser and ice maker so the appliance fills on command.
• Stops water flow when the dispenser is idle to prevent overfilling and dripping.
• Common symptom: no water from dispenser or ice maker.
• Common symptom: slow fill, irregular dispensing, or visible leak at the valve area.
• Common symptom: valve hums or makes noise when energized.

• One shield water valve assembly

• Turn off power to the appliance and shut off the water supply before starting work.
• Relieve water pressure and have a towel/short hose ready for residual water in lines.
• Replace only with the matching part number; ensure electrical connectors and water lines are secured and not pinched.

The Ground Screw is an OEM part for GE dryers. It ensures proper grounding and electrical safety for your dryer. This screw securely connects the ground wire to the dryer chassis, providing a path for electrical current to safely discharge in the event of a fault or power surge.

A bad Ground Screw can lead to electrical issues and potential safety hazards. Causes of a bad Ground Screw can include corrosion, loose connections, or damage due to accidental mishandling or improper installation.

Symptoms of a bad Ground Screw include:

• Intermittent dryer operation
• Visible signs of damage or deterioration on the screw or ground wire
• Tripped circuit breakers or blown fuses

Replace your faulty or damaged Ground Screw with this genuine OEM GE part to ensure proper grounding and electrical safety for your dryer. 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This Holder Top Panel secures the appliance's top panel and helps keep controls and components stable for reliable operation. It replaces a worn or damaged top-panel retainer to restore proper fit and alignment. What it does:

• Secures and supports the top panel so adjacent controls and trim sit correctly
• Prevents top-panel movement that can cause noise, rubbing, or loose trim
• Restores proper panel alignment after damage or wear
• Helps maintain a secure fit between the top panel and the appliance cabinet

• 1 Holder Top Panel

• Turn off power to the appliance before beginning any repair to avoid electrical shock
• Handle edges carefully; use gloves to protect hands from sharp sheet-metal edges
• Remove and retain fasteners and trim pieces in the order they were removed for proper reassembly