Parts for Dcs BGB48-BQRN-70494A: Cart Assy Parts

This is a stainless steel hex head bolt used to secure appliance panels and components. Sold as a 10-pack, it provides durable, corrosion-resistant fasteners for routine repairs and reassembly. What it does:

• Fastens panels, brackets, and assemblies with a 1/4-20 thread and 1/2" length
• Full-thread design ensures grip along the fastener for secure clamping
• Stainless steel construction resists rust and corrosion in moist environments
• Commonly used when stripped, missing, or damaged bolts cause loose parts or rattling

• Use the correct 1/4" socket or wrench and avoid overtightening to prevent thread damage
• Replace matching fasteners in sets when possible to maintain proper fit and torque
• Wear safety glasses when working around panels and springs; disconnect power if working near electrical components

This door header is the top cabinet trim piece that finishes the refrigerator door opening and helps align the door appearance. It restores a clean, factory look and covers the gap between the cabinet and door. What it does:

• Provides cosmetic finish along the top of the door opening to restore original appearance
• Helps maintain proper door alignment by fitting into the cabinet header area
• Covers and protects the cabinet edge from wear and scratches
• Common symptom: dinged, cracked, or missing top trim that exposes the cabinet edge or creates a visible gap

• One door header trim piece as shown

• High-level replacement: remove the old header by releasing any clips or screws, then snap or fasten the new header into place
• Use appropriate tools and avoid forcing the piece to prevent damage to trim or cabinet
• Keep parts and screws organized; verify fit before final tightening

A pack of stainless steel keps (locking) nuts used to secure assemblies where a captive washer-style nut is needed. Corrosion-resistant stainless construction helps maintain a reliable hold in wet or humid appliance areas. What it does:

• Provides a captive washer and nut in one fastener for easier installation and improved retention
• Secures panels, brackets, and small hardware where a 1/4-20 thread is specified
• Resists rust and corrosion in appliance environments thanks to stainless construction
• Helps stop loosening from vibration compared with plain nuts in many appliance applications

• Use the matching 1/4-20 bolt or screw; do not force mismatched thread sizes
• Hand-start fasteners to avoid cross-threading, then tighten with the appropriate wrench or socket
• Wear eye protection when working around springs or tensioned components
• Inspect mating threads and replace any damaged hardware to ensure a secure fit

This rubber bumper cushions and stabilizes appliance panels and doors to reduce noise, vibration, and wear. It helps prevent metal-on-metal contact and keeps moving parts from rattling for quieter, smoother operation. What it does:

• Absorbs shock and dampens vibration between parts
• Prevents panels, doors, or racks from banging or rubbing
• Protects finishes by creating a soft contact point
• Helps maintain proper alignment of movable components

• Disconnect power or gas supply to the appliance before servicing
• Remove the old bumper and clean the mounting surface before installing
• These bumpers are typically installed by pressing into a hole or seating against a surface; follow the OEM instructions for your model
• If adhesive is required, use only the manufacturer-recommended adhesive and allow proper cure time

This is a 8-32 x 1-inch Torx flat-head screw used to secure panels and components on compatible appliances. Durable hardware replacement that restores proper fastening and reduces rattles or loose parts. What it does:

• Fastens panels, brackets, and internal components where an 8-32 x 1 Torx flat-head screw is specified
• Restores secure mounting to stop vibration, rattling, or misalignment caused by missing or worn screws
• Matches OEM thread size and head style for proper fit in specified mounting holes
• Suitable for metal-to-metal and sheet-metal fastening in appliance assemblies

• 10 8-32 x 1-inch Torx flat-head screws

• Use the correct Torx driver for a snug fit; avoid stripping the head
• Hand-start screws to ensure proper alignment before final tightening
• Do not overtighten; snug until secure to avoid thread or component damage
• Disconnect power and follow appliance safety procedures before servicing