Parts for Ge PDCE1NBWCDWW: 06 - Case Parts

Secures the hinge cover to your refrigerator door or cabinet hinge. Replace this screw if it's missing, stripped, or damaged to stop the cover from loosening.

Covers the base of your refrigerator beneath the door. Replace if cracked, broken, discolored, or missing to restore appearance and protect components.

Base grille cover that installs at the bottom front of your refrigerator. Replace if cracked, broken, or missing to restore the finished look.

This silicon controlled rectifier (SCR) is a replacement control semiconductor that helps regulate power to heating elements and motors, restoring proper cycle control and heat delivery in compatible appliances. What it does:

• Controls and chops AC power to heating elements or motor circuits for variable heat/speed control
• Can stop intermittent or no-heat conditions caused by a failed SCR in oven, range, or similar appliances
• Helps restore stable thermostat/regulation behavior when the original SCR is not switching correctly
• Commonly used where precise power control is required in the appliance's control board or module

• One silicon controlled rectifier (SCR) as shown

• High-level, service-only replacement — disconnect power before starting work
• Verify correct part number on the appliance and transfer heat sinks or mounting hardware if required
• Use proper ESD precautions when handling semiconductor components

Hex washer head screw for refrigerator component mounting. Replaces missing, stripped, or damaged fasteners on brackets, panels, and covers.

White plastic clip that secures the rear of refrigerator shelves or drawer rails to the cabinet wall. Replace if cracked, broken, or missing.

Right-hand center hinge assembly for refrigerator doors. Replace this hinge if your original is cracked, bent, or worn, causing door misalignment.

This is a silicon controlled rectifier (SCR) used in appliance control circuits to regulate power to heaters or motors, helping the appliance deliver consistent operation and heat when needed. What it does:

• Acts as a switch in the control circuit to regulate current flow to heating elements or motors
• Can prevent or allow power to the load based on control signals from the appliance module
• Common symptom indicators: intermittent or no heat, unit won't reach operating temperature, or inconsistent operation of the controlled component
• Used where precise control of AC power is required for safe, efficient performance

• One silicon controlled rectifier (SCR) as described

• Disconnect power to the appliance before servicing to avoid shock or injury
• Handle the part carefully; avoid bending terminals and observe anti-static precautions
• Verify wiring and terminal orientation matches the original before reconnecting

Hex head screw for securing refrigerator components and panels. Replace if screw is stripped, corroded, or missing during repairs or reassembly.

This is a replacement cover mullion screw that secures the mullion/trim cover on the refrigerator door assembly, restoring a snug, rattle-free fit and keeping the trim properly aligned. What it does

• Secures the mullion or center trim cover to the refrigerator door
• Prevents the trim from vibrating or coming loose during door use
• Addresses symptoms like a loose or rattling mullion cover
• Restores proper trim alignment for a finished appearance

• One cover mullion screw

• High-level hand tools (screwdriver) are typically all that's needed
• Tighten until snug; avoid overtightening to prevent striping the hole or damaging trim
• Disconnect power only if removal of other parts requires working near electrical components; otherwise, ensure doors are stable before working

White plastic cover cap that conceals hinge screws on your refrigerator door. Replaces worn, cracked, or missing covers for a clean finished look.

This plug cover is a small protective cap that shields an appliance's power or wiring plug/terminal area from dust and accidental contact. It helps keep connections clean and reduces the risk of debris buildup. What it does

• Covers and protects an exposed appliance plug or terminal connection
• Helps prevent dust, dirt and small debris from entering the plug area
• Reduces risk of accidental contact with terminals while appliance is serviced or idle
• Commonly used when a cord or plug is not in use or during maintenance

• No special tools required; push the cover firmly into place over the plug or terminal
• Ensure the appliance is powered off and unplugged before servicing nearby components
• Inspect the cover for damage and replace if cracked or deformed
• Not intended to alter electrical connections or provide waterproofing; use only as a protective cap

Replacement plug cover for your refrigerator. Installs over plug openings to provide a finished look. Order when original is cracked, broken, or missing.

Replacement closure spring for refrigerator doors and panels. Installs at hinge points to provide smooth closing action. Needed when original is broken, stretched, or missing.

White corner cap cover for side-by-side refrigerators. Replaces cracked, broken, or missing corner trim pieces. Restores clean appearance.

This replacement corner cap restores the finished edge and protective cover on an oven door corner for a clean appearance and proper fit. It replaces a cracked, chipped, or missing corner that can catch debris or show damage. What it does:

• Covers and protects the outer corner of the oven door from chips and dents
• Helps maintain a smooth door edge so the door closes and seals properly
• Improves cosmetic appearance when the original corner is cracked or worn
• Reduces sharp or rough edges that can catch on clothing or cause minor cuts

• Turn off power to the appliance and allow the oven to cool before servicing
• Installation may require partially removing the oven door or trim; have basic hand tools ready
• Handle the door and trim carefully to avoid scratching finished surfaces

Front roller assembly for refrigerators. Mounts to the base to enable smooth movement and leveling. Replace if cracked, worn, or mobility is impaired.

Secures mobility components and wheel brackets on side-by-side refrigerators. Replace if screw is missing, stripped, or worn to restore stable mounting.

Replacement door closure spring for refrigerator hinges. Installs on door hinge assembly to provide tension for proper closing. Needed when broken or worn.

Sheet metal screw secures refrigerator panels, trim, and brackets. Replace missing, stripped, or corroded screws to restore proper fit and assembly.

The refrigerator leveling screw is an adjustable threaded leg located at the bottom corner of your refrigerator that lets you raise or lower that corner to achieve a level, stable position. Proper leveling ensures the doors swing shut on their own and that the refrigerator runs efficiently. Replace or adjust this part if your refrigerator rocks on the floor, the doors won't stay closed, or you notice uneven gaps around the door seals.

Leg bracket assembly for refrigerators. Mounts to the base to secure and support adjustable legs. Replace if cracked, bent, or broken to restore stability.

Interior light not working when door opens? This light switch controls refrigerator illumination. DIY-friendly install takes 30-45 minutes with video.

Freezer door closure lever arm for refrigerators. Installs inside the freezer compartment to activate door sealing. Replace if cracked or broken.

Replacement lever arm for refrigerator freezer door closure mechanism. Installs on door hinge assembly. Needed when original is broken or worn.

Lever arm closure component for refrigerator freezer drawers. Mounts in base channel and works with cam to auto-close drawer. Replace if broken or missing.

Freezer door closure lever arm for refrigerators. Mounts inside the freezer compartment to control door closing mechanism. Replace if broken or worn.

Hex head screw for refrigerator panels, brackets, and assemblies. Replaces missing, stripped, or rusted fasteners to secure components properly.

Replacement door hinge closure for your refrigerator. Installs on the door frame to secure the hinge assembly. Needed when original is cracked or broken.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Fastens refrigerator panels, brackets, and internal components. Replace this screw if the original is missing, stripped, or damaged to restore secure mounting.