Parts for Ge ZFGP21HXCSS: 07 - Case Parts

Purifies water before reaching your dispenser and ice maker. Replace every 6 months for clean, safe drinking water. Verify fit with your model number.

Covers the base of your refrigerator beneath the door. Replace if cracked, broken, discolored, or missing to restore appearance and protect components.

Hex washer head screw for refrigerator component mounting. Replaces missing, stripped, or damaged fasteners on brackets, panels, and covers.

White plastic clip that secures the rear of refrigerator shelves or drawer rails to the cabinet wall. Replace if cracked, broken, or missing.

This is a silicon controlled rectifier (SCR) used in appliance control circuits to regulate power to heaters or motors, helping the appliance deliver consistent operation and heat when needed. What it does:

• Acts as a switch in the control circuit to regulate current flow to heating elements or motors
• Can prevent or allow power to the load based on control signals from the appliance module
• Common symptom indicators: intermittent or no heat, unit won't reach operating temperature, or inconsistent operation of the controlled component
• Used where precise control of AC power is required for safe, efficient performance

• One silicon controlled rectifier (SCR) as described

• Disconnect power to the appliance before servicing to avoid shock or injury
• Handle the part carefully; avoid bending terminals and observe anti-static precautions
• Verify wiring and terminal orientation matches the original before reconnecting

Fix inconsistent cooling or excess moisture in your refrigerator with this humidity sensor. Direct replacement part restores proper climate control.

Protective housing cover for refrigerator humidity sensor. Replaces cracked, broken, or missing covers. Installs in fresh food compartment.

Fix inconsistent cooling or frost buildup with this refrigerator humidity sensor. Monitors moisture levels to optimize defrost cycles. Direct replacement.

Replace your refrigerator's center hinge assembly if the door sags, misaligns, or won't close properly. This adjustable left-hand hinge connects doors.

Adjustable hinge pin that installs in the door hinge bracket to provide a pivot point. Replace when worn, loose, or damaged to restore door alignment.

Replacement closure spring for refrigerator doors and panels. Installs at hinge points to provide smooth closing action. Needed when original is broken, stretched, or missing.

This replacement corner cap restores the finished edge and protective cover on an oven door corner for a clean appearance and proper fit. It replaces a cracked, chipped, or missing corner that can catch debris or show damage. What it does:

• Covers and protects the outer corner of the oven door from chips and dents
• Helps maintain a smooth door edge so the door closes and seals properly
• Improves cosmetic appearance when the original corner is cracked or worn
• Reduces sharp or rough edges that can catch on clothing or cause minor cuts

• Turn off power to the appliance and allow the oven to cool before servicing
• Installation may require partially removing the oven door or trim; have basic hand tools ready
• Handle the door and trim carefully to avoid scratching finished surfaces

Front caster assembly that mounts to the bottom of your refrigerator. Replace if cracked, broken, or worn to restore smooth rolling and stability.

Secures mobility components and wheel brackets on side-by-side refrigerators. Replace if screw is missing, stripped, or worn to restore stable mounting.

Replacement door closure spring for refrigerator hinges. Installs on door hinge assembly to provide tension for proper closing. Needed when broken or worn.

Sheet metal screw secures refrigerator panels, trim, and brackets. Replace missing, stripped, or corroded screws to restore proper fit and assembly.

The refrigerator leveling screw is an adjustable threaded leg located at the bottom corner of your refrigerator that lets you raise or lower that corner to achieve a level, stable position. Proper leveling ensures the doors swing shut on their own and that the refrigerator runs efficiently. Replace or adjust this part if your refrigerator rocks on the floor, the doors won't stay closed, or you notice uneven gaps around the door seals.

Leg bracket assembly for refrigerators. Mounts to the base to secure and support adjustable legs. Replace if cracked, bent, or broken to restore stability.

Interior light not working when door opens? This light switch controls refrigerator illumination. DIY-friendly install takes 30-45 minutes with video.

Freezer door closure lever arm for refrigerators. Installs inside the freezer compartment to activate door sealing. Replace if cracked or broken.

Lever arm closure component for refrigerator freezer drawers. Mounts in base channel and works with cam to auto-close drawer. Replace if broken or missing.

Hex head screw for refrigerator panels, brackets, and assemblies. Replaces missing, stripped, or rusted fasteners to secure components properly.

Replacement door hinge closure for your refrigerator. Installs on the door frame to secure the hinge assembly. Needed when original is cracked or broken.

Door hinge closure assembly for your refrigerator. Installs on the door frame to secure the hinge mechanism. Replace if cracked, broken, or worn.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Replacement top mullion striker bracket for your refrigerator. Secures the door alignment system between compartments. Replace if cracked or broken.

This cover top striker secures the appliance door/cover to the cabinet so the door latches properly and stays closed. Durable replacement for worn or broken striker assemblies to restore reliable door engagement. What it does:

• Provides the contact point for the door latch/strike to engage and hold the door closed
• Replaces damaged or worn striker that can cause a door to fail to latch or pop open
• Helps stop rattling or misalignment caused by a broken strike surface
• Works with the original latch mechanism to maintain proper door positioning

• Disconnect power to the appliance before beginning any repair
• Remove outer door or top cover panels as required to access the striker
• Retain and reuse any original screws or clips unless replacement hardware is specified
• Align striker with latch mechanism and tighten securely; do not force or overtighten

Fastens refrigerator panels, brackets, and internal components. Replace this screw if the original is missing, stripped, or damaged to restore secure mounting.

This hinge shim restores proper door/lid alignment by spacing the washer hinge where wear or misalignment causes rubbing or improper closing. It's a simple replacement that helps quiet operation and improves fit. What it does:

• Provides precise spacing at the hinge to correct lid/door misalignment
• Reduces rubbing, scraping, and uneven contact during operation
• Helps restore smooth opening and closing of the washer lid/door
• Can prevent premature wear on the hinge and mating surfaces

• Disconnect power to the appliance before beginning any work
• Remove the hinge fasteners to access the worn area and install shim as needed
• Use basic hand tools; keep hardware organized during reassembly