Parts for Lg GM-B298NSSH: Case Parts

Replace your refrigerator's rear handle if it's cracked, broken, or missing. This structural support handle mounts to the back panel of your unit.

Drain tray assembly that collects condensation beneath your refrigerator. Replace if cracked, broken, or missing to prevent water leakage issues.

Replace your refrigerator's water filter cover to protect the filtration system and maintain proper seal. Essential when cover is cracked or missing. Confirm fit with your model number.

Secures the drier assembly to the refrigerator frame. Replace if the clip is cracked, broken, or missing to restore stability and reduce movement.

Control panel unresponsive or erratic? This protective cover shields your refrigerator's circuit board from moisture and debris. Straightforward install.

Refrigerator won't cool or motor keeps shutting off? The overload protector prevents compressor damage by cutting power during overheating. Simple fix.

Refrigerator roller wheel for leveling and mobility. Replaces worn, cracked, or broken rollers that prevent smooth movement or proper leveling.

This is a small retainer clip that secures the compressor in place at the base of the refrigerator. It helps prevent the compressor from shifting or vibrating excessively during operation. Replace this clip if your refrigerator produces unusual rattling or vibrating noises from the back, or if the compressor appears loose or has shifted from its mounting position.

Secures and pivots the center refrigerator door for proper alignment and sealing. Replace if your door sags, won't close fully, or pivots roughly. Verify fit by model number before ordering.

Refrigerator won't power on or no electrical connection? This power cord assembly connects your refrigerator to the wall outlet. Direct plug-in part.

Fix a refrigerator that's too warm or won't cool properly. This sensor control board reads temperature sensors and signals the main control board.

Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.

Fix refrigerator lights staying on or not turning off when door closes. This magnetic door switch is a common solution. Simple DIY repair in 15 minutes.

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

Restores clean-tasting water and steady flow by filtering sediment and contaminants. Replace every 6 months or when flow weakens. Verify fit with your model.

If your refrigerator display is dead, shows error codes, or behaves unpredictably, this sub PCB assembly processes inputs and controls specific functions.

Adjustable leveling leg that threads into the refrigerator base frame to support and stabilize the unit. Replace worn, broken, or missing legs.

Fix uneven cooling or warm spots in your refrigerator with a new evaporator fan blade. This part circulates cold air throughout the unit for consistent temps.

Drier assembly for refrigerators. Installs in the sealed refrigerant system to remove moisture and contaminants. Replace if damaged or worn during repair.

Fix ice buildup in your refrigerator with this defrost heater. Melts frost from the evaporator during defrost cycles to restore consistent cooling.

Plastic drain tube that channels defrost water from evaporator coils to drain pan. Replace if cracked, melted, broken, or causing water leaks in freezer.

Refrigerator making loud noise or not cooling evenly? This fan assembly circulates air to eliminate hot spots and restore consistent temperatures.

Supports and stabilizes your refrigerator door for proper alignment. Replace if bracket is cracked, broken, or causing door misalignment issues.

This is a rubber or elastomer damper that supports and isolates the evaporator fan motor inside the refrigerator. It absorbs vibration from the motor to reduce noise during normal operation. Replace this part if you hear excessive buzzing, rattling, or vibration coming from the freezer section, which often indicates the damper has hardened or deteriorated.

The Temperature Sensor is an OEM part for LG refrigerators. Also known as a thermistor, is responsible for sensing the temperature changes and providing the necessary feedback to the refrigerator's control board. It helps maintain accurate and consistent temperature levels, ensuring optimal food preservation and efficient cooling.

Causes of a faulty temperature sensor can include wear and tear over time, damage due to electrical issues or exposure to extreme temperatures, or sensor calibration issues. These factors can result in temperature inconsistencies, inaccurate readings, or improper cooling performance of the refrigerator.

Symptoms of a bad temperature sensor may include:

• Incorrect temperature readings on the control panel
• Temperature fluctuations inside the refrigerator
• Overcooling or inadequate cooling of food items

This OEM LG part can also be used on Kenmore/Sears appliances.