Parts for Craftsman 358341180: Chain Saw Parts

This authentic OEM part is a replacement momentary switch meant for a chainsaw or edge trimmer. Also known as a kill switch, a momentary switch acts as a safety measure to immediately shut off the appliance's motor. If the user begins to lose control of the appliance, they can simply hit the momentary switch and the engine will disengage even if it is not currently in the off position. This helps to prevent accidents and bodily harm. When engaged, the engine requires a five second waiting period before it can restart. Over time and through repeated use, switches can naturally become worn out. They may also be damaged if knocked against something hard on accident. Replacing this switch will require a screwdriver to access the switch located in the handle of the appliance. Once accessed, the switch can easily be replaced by detaching the wires and inserting the new part. Be sure to follow the user's manual as this process will vary depending on the appliance. This part is sourced directly from its original manufacturer and will work with Poulan and Weed Eater appliances. This part ships individually.

This replacement part is a pinion gear. It is a genuine replacement part made by Husqvarna. This part is typically found in chainsaws and helps the spinning and turning mechanism of the chain to operate properly during use.A new pinion gear might be needed if the user notices that the chain in the chainsaw is not rotating properly or smoothly. This can be due to a stripped pinion gear and the problem should be fixed once the part is replaced. Be sure to wear work gloves as the user will be working closely to the blades in the chainsaw. Refer to the user manual for more detailed information on how to replace this specific part. This pinion gear is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit.

This is a replacement chainsaw retaining ring. The sprocket is commonly attached to the gear drive shaft in chainsaws with a retaining ring. If the original retaining ring becomes damaged, the chainsaw will not operate properly.Needle-nose, snap ring, or retaining ring pliers may be required to remove the old, damaged retaining ring. To install the new retaining ring, snap ring or needle-nose pliers should be placed into the small holes located on the new retaining ring. Then, slightly open the pliers to pull back the retaining ring's arms, opening up the ring center. Careful attention should be paid while opening the retaining ring to avoid overstretching. Overstretching the retaining ring would lead to the sprocket not correctly attaching to the chainsaw's gear drive shaft. Finally, with proper sizing, the retaining ring can be placed over the wheel grove, attaching the sprocket to the drive shaft.This retaining ring is an OEM part that is sourced directly from the manufacturer. This retaining ring is designed to replace damaged rings in Poulan, Poulan Pro, Husqvarna, and Craftsman chainsaws. The retaining ring is sold individually.

This is genuine OEM replacement pinion designed for use with select chainsaws. The pinion works in combination with the sprocket/gear sprocket to rotate the chain. The power is delivered to the pinion, which rotates and then causes the sprocket to rotate, leading to the chain action that is needed for a chainsaw to work. Over time, gears and sprockets can get worn down with regular use. They may also be damaged by other incidents or fail as a result of another repair that wasn't taken care of promptly. Any drive assembly parts, including this pinion, should be replaced immediately in the event that they do fail. This OEM pinion is manufactured to strict standards by Husqvarna. The part is compatible with multiple models of chainsaws and dozens of brands including Craftsman, Poulan, and Poulan Pro. Also known as the drive gear, this pinion is made of durable materials and is sold individually. In some cases, people may want to purchase the entire drive assembly, but that may not be necessary. This is where replacing just the pinion can be a good choice. Be sure to wear gloves and allow the chainsaw's engine to cool completely before doing any repairs.

This is a standard chainsaw bar. The bar holds the chain in place so that it can spin and cut. Of course, if the bar has been damaged, the chain might not be able to stay on. This could mean that users can't use the machine and trying to use the chainsaw could be dangerous. If there are any issues with the bar, it should be replaced as soon as possible.Accidents and dropping the chainsaw could cause it to bend or even break. Llet the machine cool, take off the old chain, and then remove and replace the old bar.This standard chainsaw bar can work with chainsaws from Craftsman, Poulan, and Oregon. This is a genuine OEM replacement, and it is sold individually.

The chainsaw thumb wheel assembly, sometimes called a wheel gear assembly or a chainsaw knob, is an important part of the chain adjustment system. Turning the wheel will allow users to tighten or loosen the chain on the saw. The thumb wheel assembly, made of plastic and metal, could become worn down or broken over time, which will require a replacement. If this part of the chainsaw is not working properly, it will not be possible to make adjustments to the chain's tension. Owners would not be able to remove their old chain or add a new one. The new thumb wheel assembly is easy to install and will get the chainsaw back in working order. The authentic OEM chainsaw thumb wheel assembly is sold individually. It is compatible with models from Husqvarna, Poulan, Poulan Pro, and Craftsman. Buyers should consult their manuals to ensure they are getting the correct part for their chainsaw's make and model.

This replacement part is a chain tensioner pin and is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. This pin is a common part in many types of machinery and appliances. The pin places tension on the bar when it is adjusted. A new pin might be needed if the current one has become stripped or damaged overtime. This can be due to normal wear and tear and is very common. This repair should be fairly simple and only require a screwdriver and a socket. Be sure to refer to the owner's manual for more detailed instructions on how to replace this part. Be sure the appliance is shut down before beginning a repair. This tensioner pin is sold individually and is sourced directly from the manufacturer to ensure a proper fit and long lasting use. This is a genuine OEM replacement part made of durable metal.

This adjusting screw is a genuine Husqvarna part. It is manufactured for use with both gas and electric chainsaws. It is located in the clutch housing of the chainsaw and used to adjust the bar. If adjustments are made frequently, then it is normal for the adjusting screw to suffer wear and tear and require replacement. One of the most common damages to an adjusting screw is stripping.This adjusting screw is a genuine OEM part sourced directly from the manufacturer, although it has been discontinued by the manufacturer, and limited supplies remain. It is sold individually, so be sure to order more than one if needed. Replacing a damaged adjusting screw is an easy repair that requires only a screwdriver and Allen wrench. This adjusting screw was made for compatibility with several models of chainsaws made by Craftsman, Husqvarna, and Poulan but may also work with models made by AYP, Jonsered, McCulloch, RedMax, Weedeater, Yard Machines, and Yard-Man.

This is a six-pin sprocket used in many models of chainsaws. The sprocket is an integral component of a chainsaw since it drives the chain on the machine, transfering the power to the chain so it can cut through wood effectively. Due to the high speeds and vibrations created by the chain, this item may become worn out and need to be replaced. The best way to determine whether the sprocket is worn out is by manually rotating the chain on the chainsaw. If the chain is tensioned correctly and the chain rotates smoothly before becoming loose or hard to turn, the sprocket likely has worn teeth. This can be checked by loosening the bar nuts and taking off the bar, chain, and cover. The sprockets will be exposed and an inspection can be done visually. Look for teeth that are grooved or notched, which indicates the sprocket will need to be replaced.This six-pin sprocket is a genuine OEM replacement part that is sourced directly from the manufacturer. The component is sold individually. The sprocket is compatible with various chainsaws manufactured by Craftsman, Poulan, and Poulan Pro.

This is a replacement oil cap for a variety of small gasoline-powered tools they build. These devices include power saws, chainsaws, trimmers, and pruners. The oil cap is tethered to the oil tank, granting easy access to the engine oil for filling or replacement while preventing outside contaminants from getting into the oil basin and, thus, the crankcase. While the cap is not a moving part, it is one of the most exposed pieces of this work equipment. As such it collides with multiple heavy objects such as other tools, trees, cement structures, and truck beds. This type of wear and tear can cause the interior threads of the cap to warp so that the cap cannot be closed tightly. The cap can also be damaged so that it leaks. For safety reasons as well as for the proper operating condition of the equipment, a damaged oil cap should be replaced immediately. Make sure when removing the old cap that the tether is completely freed from the power tool, and make sure the new tether is properly attached. This replacement cap is a genuine OEM part, built to the same specification as the factory original piece and fits Ryobi and Poulan machines.