Parts for Kitchenaid KDRP463LSS02: 08 - Chassis Parts, Miscellaneous Parts

Replacement mounting screw for securing panels, brackets, covers, and trim pieces in appliances. Restores fit when hardware is missing, stripped, or lost.

Secures washer door handles to the outer panel. Replace if stripped, missing, or damaged to restore a tight handle fit and prevent loosening.

Secures washer door handles to the outer panel. Replace if stripped, missing, or damaged to restore a tight handle fit and prevent loosening.

Secures cooktop panels, burner components, and trim pieces. Replace missing, stripped, or damaged screws to eliminate rattles and keep parts aligned.

Replacement mounting screw for securing panels, brackets, and components in appliances. Needed when original fastener is missing, stripped, or damaged.

Secures cooktop panels, burner components, and trim pieces. Replace missing, stripped, or damaged screws to eliminate rattles and keep parts aligned.

This harness jumper for a valve is a factory-style replacement wiring connector that restores a secure electrical link between the appliance wiring and the valve solenoid(s), helping re-establish reliable valve operation. What it does

• Provides the correct plug-and-wire connection to the valve solenoid(s) so the control can activate the valve
• Replaces damaged, corroded, or melted connectors that cause intermittent or failed valve operation
• Commonly used when valves do not open or close, or when related error codes indicate an open or shorted circuit
• Helps prevent loose connections that can lead to arcing or erratic component behavior

• One harness jumper (valve) as pictured

• Disconnect power to the appliance before starting any repair
• Turn off the water supply if working on water valves or lines
• Match connector shape and wire colors to the original before installing; do not force connections

Specs: 25ft, 14 Ga. 150 c Black

Size: 1/3 oz.

Size: 25ft, 12 Ga. 150 c Black

Replace a missing, stripped, or damaged ground screw on your oven. This screw secures grounding connections for safe electrical operation.

Specs: 25ft, 14 Ga. 150 c Blue

Specs: 25ft, 14 Ga. 150 c Brown

Specs: 25 ft, 14 Ga., 150 c Green

Splicing 25 Ft. Black 12 Ga. 150~c (Wire, Orange 14 Ga. 150~c)

Splicing 25 Ft. Black 12 Ga. 150~c (Wire, Red 14 Ga. 150~c)

Splicing 25 Ft. Black 12 Ga. 150~c (Wire, Yellow 14 Ga. 150~c)

Splicing 25 Ft. Black 12 Ga. 150~c (Wire, Red 14 Ga. 200~c)

Replace your range access panel seal to prevent heat loss and maintain efficiency. Essential when worn or damaged. Verify fit with your model number.

Replace a cracked or missing side rail grommet on your oven rack. This small plastic grommet fits into the rack rail to provide smooth gliding and support.

Lp converstion kit.

Specs: 25ft,14 Ga., 200 c Brown

Anti-tip bracket that secures your range to the wall or floor. Replace if broken, bent, missing, or during installation to prevent tipping hazards.

Secures wiring bundles inside your microwave. Replace this wire tie if it's cracked, broken, or missing to keep internal wires organized and secure.

Wire harness for cooktops. Routes electrical signals between components. Replace if wiring is damaged, frayed, or connectors are worn or broken.

Non-corrosive silicone adhesive sealant for appliance repairs. Replace cracked or missing seals on door panels, trim strips, and interior edges.

Replacement hex nut for dryer terminal blocks and electrical connections. Secures terminal components. Needed when original is stripped, missing, or damaged.

Kit of 4 pins that insert into oven door hinges to safely remove the door for repairs or cleaning. Replace lost or damaged pins during door removal.

Replacement mounting screw for securing panels, brackets, covers, and trim pieces in appliances. Restores fit when hardware is missing, stripped, or lost.