Parts for Whirlpool SF3020EKT3: 04 - Chassis Parts

Torsion spring for electric and gas ranges. Mounts inside the oven door hinge assembly to counterbalance door weight. Replace if broken, worn, or missing.

Color: Biscuit. For white use WP98010042. For black use WP98010043

Color: White. For biscuit use 98010045. For black use WP98010043

Fix a rattling oven floor with this bottom panel clip. Secures the oven panel to the chassis, stopping noise and keeping it locked in place. Easy install.

Adjustable front leveling leg threads into the base corner of your range to raise or lower the unit. Replace if broken, cracked, or missing to level your range.

Adjustable leveling leg installs on the front or rear corners of your range. Replace if broken, cracked, or worn to stabilize and level your appliance.

Replacement metal panel that sits under the oven cavity. Restores a clean, heat-resistant surface when original is warped, corroded, or damaged.

Secures the thermostat sensor bulb in place on your range. Replace if broken or corroded to restore accurate temperature control. Verify fit by model.

Replacement base baffle for your range. Installs at the bottom to provide structural support and proper airflow. Order a new one if damaged or missing.

This replacement bumper cushions and protects appliance panels and doors to reduce vibration, prevent chipping, and stop rubbing or rattling. It restores a quiet, secure fit where the original bumper has worn or fallen off. What it does:

• Acts as a soft stopper to prevent doors, drawers, or panels from banging or contacting metal surfaces
• Reduces vibration and rattling during operation
• Protects finishes from chips, scratches, and wear at contact points
• Helps restore proper alignment and snug fit where the original bumper is missing or compressed

• One replacement bumper (1 count)

• Clean and dry the mounting surface; remove any old adhesive or debris before installing
• Press the bumper firmly into place; some bumpers use adhesive backing or fit into a recess—verify fit before final placement
• If adhesive is used, allow time for proper bonding per adhesive instructions; avoid using the appliance until secure
• For safety, disconnect power to the appliance before accessing panels or doors

Replacement U-nut for electric and gas ranges. Secures components and panels in place. Order a new nut if yours is stripped, missing, or damaged.

Restores a heat-resistant seal around your oven door. Replace when torn or damaged to maintain accurate temperatures and contain heat. Confirm fit by model.

Factory replacement screw that secures appliance components and hardware. Use it to replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and help prevent loosening or damage from vibration.

• Fastens brackets, panels, or internal parts at the original mounting points
• Replaces worn or missing hardware to correct loose or misaligned components
• Helps reduce vibration-related noise and movement
• Matches the original thread and length specified for the application

• Disconnect power; shut off water or gas if applicable before servicing
• Compare to the original for thread and length match before installation
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• Reuse any original spacers/washers if present; replace if damaged

Replace a cracked, worn, or missing washer on your range. This small metal or rubber part provides spacing and protection between components during assembly.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

Note: This part is one screw, order quantity needed.

Replacement power cord for gas ranges. Installs to restore main electrical connection. Order when original cord is frayed, cut, melted, or damaged.

Right hand side

Left hand side

Replace your range's insulation cap if it's cracked, broken, or missing. This protective cover installs over insulation to maintain proper heat retention.

Secures insulation in your range to maintain proper heat retention and efficiency. Replace if damaged, loose, or missing to prevent insulation shifting. Confirm fit with your model number.

Insulation batting installs between inner and outer oven walls to retain heat. Replace if damaged, cracked, infested, or missing for proper temperature.

Secures insulation in your range to maintain proper heat retention and efficiency. Replace if damaged, loose, or missing to prevent insulation shifting. Confirm fit with your model number.

Insulation batting installs between inner and outer oven walls to retain heat. Replace if damaged, cracked, infested, or missing for proper temperature.