Parts for Frigidaire HFA180FM2D: 02 - Chest Freezer Parts

This part has been discontinued by the manufacturer and is no longer available.

This small hinge spacer positions and supports the refrigerator door hinge assembly to ensure proper door alignment and smooth opening. It helps restore correct door spacing and prevents rubbing or uneven sealing when the hinge is worn or misaligned. What it does:

• Provides precise spacing between hinge components so the door sits and closes correctly
• Stabilizes the hinge wing to reduce door wobble and uneven movement
• Helps correct minor misalignment that can cause door binding or uneven gaps
• Works with the hinge assembly hardware to maintain consistent door sealing

• One hinge wing spacer as shown

• Intended for use with the door hinge assembly; verify hinge location before ordering
• Basic hand tools typically required; refer to your model's service manual for disassembly steps
• Disconnect power and empty the door as needed to avoid injury during service
• If hinge damage or heavy wear is present, replace the entire hinge assembly rather than only the spacer

This part has been discontinued by the manufacturer and is no longer available.

The Freezer Door Key is an OEM replacement part for Frigidaire refrigerators. This small but essential component is designed to securely lock the freezer door, preventing accidental openings or unauthorized access.

Symptoms of needing to replace the freezer door key include:

• Difficulty in locking or unlocking the freezer door
• The key not fitting properly or becoming stuck in the lock
• Visible wear, damage, or breakage of the key itself

Causes of a faulty freezer door key can include normal wear and tear over time, physical damage due to impact or mishandling, or issues with the locking mechanism itself.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

By Frigidaire. Includes Freezer key 5303310289.

Size: Approximate 2.5 inches thick, 33 inches wide and 70 inches long.

This part has been discontinued by the manufacturer and is no longer available.

Quantity of 1 clip.

Note: See kit# 5303922007 and 5304406520.

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

Includes service line.

This rubber compressor mounting grommet cushions and isolates the compressor to reduce vibration and noise that can transfer to the cabinet. It helps maintain stable compressor positioning for quieter, smoother operation. What it does:

• Absorbs compressor vibration to lower noise and rattling
• Dampens movement that can cause abrasion or wear on mounting hardware
• Helps maintain proper alignment of the compressor assembly
• Common symptom: excessive buzzing, vibration, or rattling from the back of the appliance

• Always disconnect power to the appliance before servicing.
• Support the compressor before removing mounts to prevent shifting or damage.
• Inspect surrounding mounts and hardware; replace any worn or damaged pieces.

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener