Chore Performer

Wave washer helps secure fasteners and improve operation on lawn mowers and walk-behind equipment. Direct fit replacement part for push and self-propelled models.

Lock washer prevents fasteners from loosening due to vibration in lawn mowers, snowblowers, and outdoor power equipment. Simple replacement part.

Flat washer for lawn tractors and riding mowers. Installs with bolts and screws to secure components. Replace if washer is missing or worn.

This replacement part is a screw, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This specific screw is typically found in snowblowers and is responsible for keeping different parts in place and secure. A new screw might be needed if any current ones are missing or damaged. After years of normal wear and tear screws can become stripped overtime and might need replacing. To replace this part the user should only need a common household screwdriver and possibly pliers if the screws have become wedged in an area. Overall this should be a fairly simple repair depending on the amount of new screws needed.This is a genuine OEM replacement part sourced directly from the manufacturer and is sold individually. Be sure the correct amount of screws are purchased as many machines require more than one to operate successfully.

Shield spacer for lawn tractors and riding mowers. Provides proper spacing between shield components. Replace if damaged, worn, or missing during repairs.

Shoulder bolt that secures the wheel to the frame on lawn mowers, edgers, and tillers. Replace if bolt is stripped, broken, or missing for proper wheel attachment.

This ball bearing assembly has a wide variety of uses in a number of gasoline-powered yard tools. Bearings are used to provide smooth, friction-free motion between the rotating parts of equipment where pieces fit together and move. The weight and momentum of the rotating motion are distributed to the ball bearings, which prevents wear on the equipment and allows smooth, repetitive motion. Ball bearings are used in equipment such as tillers and lawn tractors, as well as other power equipment that is self-propelled. The bearings will wear out over time since they are on the receiving end of all the angular momentum of the equipment being used. One of the chief locations where bearing assemblies need to be replaced are the drive wheels of the riding mowers and lawn tractors. The bearings are located in brass housings specifically machined to hold them. Since it can be difficult to remove the old ball bearing assemblies from these housings, it is worth considering simply replacing the entire housing as well as the bearing. These bearings are genuine OEM manufactured replacement parts. They are compatible with MTD, Yard-Man, Troy-Bilt, Husky, Cub Cadet, and Yard Machine lawn tools.

Flange bearing for snow thrower auger and drive systems. Replace if you notice unusual noise, vibration, or difficulty operating. Verify fit with your model.

This is a bushing made from black plastic with a cleft down the middle to provide enough flex for easy insertion. It has a flanged design, which means it won’t easily pop out after installation, even under stress from constant vibration. The bushing’s primary purpose is to protect wires and cables from damage as they pass through a channel. As such, the material is fairly durable and does not need to be replaced under ordinary circumstances. That said, there are some situations in which it can become damaged. For one thing, it’s easy to damage while repairing the wires or cables that run through the bushing. If the bushing does need to be replaced, it requires disconnecting any cables or wires that run through the bushing. Pop out the old bushing with a rubber mallet, install the new bushing the same way, reconnect the wires, and the repair is complete. This is an OEM part sourced directly from MTD, and it is sold individually. It was initially used on snowblowers but has also been used on lawnmowers and lawn tractors.

This flange bearing fits tightly between two connected components to create an airtight seal in a variety of types of lawn and garden equipment. With time and use of the equipment, the flange bearing can start to become damaged, break, or may be lost. When this occurs, the flange bearing will need to be replaced.Place the equipment on a flat surface and disconnect the spark plug wire. The location of the flange bearing will vary based on the equipment being used, so condult the user manual. Disassemble the tool as needed to get access to the flange bearing. It can be removed using a set of pliers. Clean off the components where the bearing was located before installing the new flange bearing. Replace the components and connect the spark plug wire.This is a genuine OEM replacement part that is sourced directly from the manufacturer. The part is sold as an individual item. The flange bearing can be used with lawnmowers, edgers, and snowblowers manufactured by MasterCut, Craftsman, Yard-Man, Cub Cadet, Montgomery Wards, Yard Machines, and MTD.

Needle bearing for lawn mowers and outdoor power equipment. Replace if you notice excessive noise, wobbling, or rough operation. Verify fit with your model.

A ball bearing is a rolling element bearing that uses balls to maintain the separation between the bearing races. This part is designed for use with outdoor lawn and garden power equipment such as snowblowers, chippers, shredders, and tillers. It is compatible with products by brands such as Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, and MasterCut.The ball bearing part is crucial because its purpose is to reduce rotational friction while supporting radial and axial loads. Without functioning ball bearings, valuable outdoor equipment would fall apart and quickly stop working. That is why it is important to get any ball bearings replaced if they are worn out or malfunctioning.This ball bearing is made out of metal. The ball bearing is an original OEM part sourced directly from the manufacturer, MTD. It is sold individually.

Sealed ball bearing reduces friction between fixed parts and rotating shafts. Replace if you hear grinding noise or notice wheel wobble. Verify fit.

Replacement blade for chipper shredders. Chops limbs and sticks into particles. Order a new blade if yours is dull, chipped, bent, or worn from use.

If your tiller clutch won't engage or disengage properly, a worn or frayed clutch control cable is likely the cause. This cable replacement restores control.

Replace a stripped or worn control cable that prevents smooth tiller operation. This cable connects user controls to machine functions for precise settings.