Parts for Kitchenaid KSM7990NP0: 01 - Color Variation Parts

This housing is the main structural body that supports and protects the appliance's internal components, restoring proper alignment and preventing damage from vibration or impact. What it does

• Provides a rigid enclosure to hold internal assemblies in place and maintain correct component spacing
• Reduces vibration and movement that can cause noise or premature wear
• Protects electrical and mechanical parts from physical damage and debris
• Helps maintain proper seals and alignments that can prevent leaks or operational issues

• One housing

• Disconnect power (and water, if applicable) before beginning any repair
• Handle part carefully to avoid cracking clips or tabs; some fasteners may be plastic
• Basic hand tools typically required;

This motor housing is the outer mounting and protective enclosure for the appliance motor, finished in white to match the cabinet. It provides a secure support for the motor and helps isolate noise and vibration. What it does:

• Supports and secures the motor assembly in the appliance
• Protects the motor from debris and contact with moving components
• Helps reduce motor noise and vibration through stable mounting
• Resolves symptoms like excessive vibration, rubbing noises, or misaligned motor mounting

• One motor housing (white)

• Disconnect power to the appliance before starting any repair
• Typical installation requires removing panels and either the drum or motor access components; follow OEM instructions
• Handle housing edges carefully and retain all mounting hardware for reassembly

This planetary assembly is the drive gear housing that transfers motor torque into the appliance's rotating mechanism, restoring reliable movement and consistent operation. It's a direct-fit replacement when the original gear housing is worn or damaged. What it does:

• Translates motor rotation into the multi-gear motion needed for the appliance's rotating parts
• Restores smooth, quiet operation when worn or failing gears cause grinding or irregular movement
• Prevents further damage to surrounding components by replacing stripped or broken gear teeth
• Supports consistent performance under normal operating loads

• Disconnect power and follow all safety procedures before servicing
• Access may require removing the appliance cabinet or specific panels; keep fasteners organized
• Inspect related seals, bearings, and mounting hardware and replace if damaged

This Support (mounting bracket) secures internal components to the appliance cabinet so parts stay aligned and operate quietly. It replaces a worn or broken support to restore stable mounting and reduce noise or movement. What it does

• Holds and stabilizes panels, assemblies or internal components to maintain correct alignment
• Prevents rubbing, vibration or shifting that can cause noise or part wear
• Helps keep connected components in their intended position for reliable operation
• Commonly replaced when cracked, broken or missing after impacts or during maintenance

• One Support (mounting bracket)

• Recommended for installers or those comfortable with appliance repair; disconnect power before service
• Inspect surrounding fasteners and mating surfaces; replace any damaged screws or clips
• Use only parts and hardware specified for your model to ensure proper fit and function

A white replacement bowl support that centers and stabilizes the appliance bowl or glass tray to reduce wobble and noise, helping restore smooth rotation and reliable operation. What it does:

• Centers and supports the bowl or glass tray to prevent off-center rotation and rubbing.
• Keeps the tray steady to reduce vibration and noisy operation.
• Helps the tray rotate smoothly for even heating or proper function.
• Common symptoms it can address: wobbling or off-center bowl/tray, noisy rotation, scraping or unstable tray movement.

• Disconnect power to the appliance before starting any work.
• Remove the bowl or glass tray and lift out the old support; inspect the drive hub or shaft for damage.
• Align the support over the hub/shaft and press into place until fully seated; do not force broken or warped plastic.

This replacement column is a molded cabinet trim piece that restores the finished appearance and edge protection on compatible refrigerator doors. It helps cover internal edges and supports proper door alignment for a clean, factory look. What it does:

• Replaces a cracked, warped, or missing cabinet column/trim piece to improve appearance
• Covers and protects exposed door or cabinet edges from wear and moisture
• Helps maintain proper door spacing and alignment for smooth operation
• Eliminates gaps that can allow dirt buildup or impair seal contact

• One replacement column

• Designed for direct swap with the original part; no special tools usually required
• Power off and empty the immediate area if working near electrical components or lights
• Handle carefully to avoid scratching the finish; use gentle pressure when seating snap features
• If fasteners or clips are damaged, replace them with OEM equivalents for secure fit

This bowl and foot assembly replaces a cracked or worn support bowl used to stabilize and support the appliance's internal component, restoring proper alignment and quiet operation. Durable molded construction suits direct-replacement needs. What it does:

• Supports and centers internal components to maintain smooth rotation and balance
• Replaces damaged, cracked, or warped bowl/foot that can cause rattling or uneven operation
• Restores correct spacing to prevent contact between moving parts and the cabinet
• Matches factory fit and finish for a secure, stable installation

• Disconnect power before beginning any repair to avoid electrical hazard
• Handle with care to avoid cracking the plastic; use gentle force when seating into place
• Basic hand tools may be needed to access the mounting area; model-specific diagram for access