Parts for Kitchenaid 5KSM175PSEVB5: Color Variation Parts

This housing is the replacement cabinet housing that supports and protects internal appliance components, restoring proper fit and appearance. It helps keep internal parts secure and maintains correct panel alignment for safe operation. What it does:

• Provides a rigid mounting surface for controls, assemblies and wiring
• Protects internal components from dust, moisture and impact
• Maintains panel alignment to reduce vibration and rattling
• Restores correct clearance and fit when an outer cabinet is cracked or warped

• Disconnect power and water before beginning any repair
• Basic hand tools required; mounting screws or clips must be reused
• Handle edges carefully to avoid cuts; wear gloves and eye protection
• Verify fit and orientation with parts diagram before final assembly

This housing is the replacement cabinet component that helps protect internal dryer components and maintain proper airflow and alignment. Replacing a damaged housing restores panel fit and helps prevent debris from reaching internal parts. What it does:

• Forms the external or internal cabinet surface that supports and protects internal components
• Helps maintain proper airflow and component alignment for normal operation
• Commonly replaced when cracked, warped, or broken from impact or wear
• Can reduce rattles, gaps, and debris intrusion when installed correctly

• Refer to your model's service manual for disassembly and reassembly instructions
• Disconnect power (and gas, if applicable) before starting any repair
• Handle edges carefully; wear gloves to avoid cuts and protect finishes
• Compare the replacement to the original part for fit before final installation

This replacement housing restores the appliance's structural cabinet where internal components mount, helping secure parts and reduce vibration. Use this housing to replace cracked, warped or damaged cabinet sections that affect fit and stability. What it does:

• Provides a rigid mounting surface for motors, controls and other internal parts
• Helps maintain proper alignment to reduce vibration, noise and rubbing
• Replaces cracked, broken or distorted cabinet sections that can allow parts to shift
• Prevents moisture and debris from reaching internal components when intact

• One housing cabinet as shown

• Disconnect power and water before starting any repair
• Basic disassembly of exterior panels may be required; retain screws and brackets
• Handle edges carefully — plastic and metal housings can have sharp edges

This replacement housing provides the structural enclosure that protects and supports internal appliance components, restoring proper alignment and helping prevent leaks or debris entry. Use it when the original housing is cracked, broken, or misshapen. What it does:

• Encloses and supports motors, pumps, or gear assemblies to keep components aligned and secure
• Protects internal parts from dust, water spray, and foreign objects
• Helps maintain proper airflow or water routing where applicable
• Reduces vibration and noise caused by loose or damaged housing
• Common symptom indicators: visible cracks or broken tabs, unusual vibration or noise, misaligned panels, or leaks near the housing area

• One replacement housing

• Disconnect power (and water if applicable) before starting any repair
• Handle housing carefully to avoid breaking mounting tabs or clips during installation
• Typical install requires basic hand tools; follow the appliance service manual for proper steps and torque specs

This housing is the outer cabinet piece that supports and protects internal components, restoring structural integrity and alignment for safe, quiet operation. It's the main exterior enclosure where internal parts mount. What it does:

• Replaces a cracked, dented or corroded outer cabinet that lets components sit out of alignment
• Helps stop rattling, vibration or scraping caused by a warped or broken housing
• Restores proper mounting points for internal assemblies and fasteners
• Protects internal wiring and components from debris and moisture

• One outer housing

• Disconnect power before starting any service; follow all safety guidelines
• Basic hand tools required; some panels or components may need to be removed first
• Inspect adjacent mounting hardware and gaskets and replace if worn for best fit

This main cabinet housing provides the structural enclosure that supports and protects internal components, restoring the appliance's original fit and finish. It helps keep parts aligned and shields circuitry and mechanisms from damage. What it does:

• Replaces a damaged or cracked main housing to restore structural integrity and proper component alignment
• Helps reduce vibration and noise caused by loose or broken enclosure parts
• Protects internal wiring, controls, and mechanical components from moisture and debris
• Restores correct mounting points for panels, latches, and internal assemblies

• One main housing

• Disconnect power and, if applicable, gas and water supplies before starting any repair
• Basic hand tools are typically required; some panels or components may need to be removed for access
• Follow OEM service instructions for proper alignment and fastener torque to ensure safe operation

This housing is the outer case panel that protects and supports internal components, restoring proper fit and appearance to the appliance. It provides structural support and shields wiring and mechanisms from dirt and damage. What it does:

• Replaces a cracked, warped or damaged outer housing to restore proper alignment and enclosure
• Keeps internal components protected from dust, moisture and impact
• Helps reduce rattling or vibration caused by a loose or broken housing
• Restores the appliance's exterior fit and finish for safe operation

• One housing

• Disconnect power (and water, if applicable) before starting any repair
• Remove trim and access panels as needed; retain fasteners for reassembly
• Handle edges carefully to avoid cuts; use proper tools and support the housing during removal/installation

This housing is the outer cabinet piece that supports and protects internal components, helping keep the appliance stable and contained. Replacing a damaged housing restores proper fit, reduces vibration, and prevents debris or water from reaching internal parts. What it does:

• Provides structural support for internal assemblies and panels
• Protects electronics, motors, and other components from impacts and contamination
• Keeps internal parts aligned to reduce rattling or excessive vibration
• Helps prevent leaks or entry of debris that can cause malfunctions
• Common symptom: visible cracks, breaks, warping, or loose/torn mounting points

• One cabinet housing

• Disconnect power (and water supply if applicable) before beginning any repair
• Handle edges carefully — housings and mounting tabs can be sharp or brittle
• Basic hand tools typically required; follow OEM instructions for disassembly/reassembly
• If clips, gaskets, or fasteners are damaged, replace them to ensure a secure fit

This replacement cover protects and secures internal components and wiring, restoring a finished appearance and helping prevent debris intrusion. It's a like-for-like exterior housing piece used on compatible Whirlpool appliances. What it does

• Covers and protects internal electronics, terminals, and wiring from dust and accidental contact
• Restores the appliance's finished exterior where the original cover was missing or damaged
• Helps maintain proper airflow paths and component positioning when installed correctly
• Can reduce vibration-related noise by keeping parts secured and enclosed

• One cover

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Removal/installation usually requires removing a few screws and lifting the old cover off; keep fasteners for reassembly
• Handle edges carefully; use gloves to avoid cuts and protect painted surfaces

This replacement cover is an access panel that protects internal components and restores the appliance's appearance. It keeps wiring and mechanical parts shielded while maintaining a clean exterior surface. What it does:

• Covers and protects internal components from dust, debris and accidental contact
• Restores the appliance's exterior finish after damage or removal
• Helps reduce rattles or vibration caused by loose or broken panels
• Provides a secure mounting surface for adjacent panels and controls

• Disconnect power (and water if applicable) before beginning service
• Use proper hand tools; avoid overtightening fasteners to prevent cracking
• Handle edges carefully to avoid cuts and to prevent cosmetic damage
• Refer to your model's service manual or parts diagram for correct placement and fastener locations

This is a decorative end cover that attaches to the body of a stand mixer. It conceals internal components and provides a finished appearance to the mixer housing. Replace this cover if it is cracked, broken, or missing, which can leave internal parts exposed.

Replace the end cover on your stand mixer when the original is cracked, broken, or missing. This cosmetic panel installs on the motor housing end.

Replacement access panel cover for stand mixers. Shields internal wiring and controls while restoring exterior appearance. Replaces cracked or missing covers.

This is a cover designed for the coin box assembly on a commercial-style dishwasher or laundry appliance. It protects the coin mechanism from tampering and debris. Replace this cover if it is cracked, broken, or missing, which can leave the coin mechanism exposed and vulnerable to damage.

White plastic back cover for stand mixers. Protects internal components at rear of motor housing. Replace if cracked, broken, or missing.

This is the planetary gear assembly for a stand mixer, which drives the rotating motion of the mixer attachments in an orbital path around the inside of the bowl. It connects the motor's output to the attachment hub, ensuring thorough and even mixing. Replace this part if the mixer head wobbles excessively, attachments spin erratically, or the mixing action becomes uneven or stops altogether.

If your mixer won't spin or makes grinding noises, the planetary gear assembly may be worn. This part transfers motor power to attachments. Moderate DIY.

This planetary gear assembly is a key component in the dishwasher's spray arm drive system, converting motor rotation into the oscillating motion needed to distribute water throughout the wash tub. It consists of a set of gears housed in a compact assembly that meshes with the motor output. Replace this part if the spray arms are not rotating properly, dishes are coming out dirty, or you hear grinding noises during the wash cycle.

Fix mixer wobbling or grinding noises with this planetary gear assembly. Essential for smooth mixing action. Moderate repair with periodic greasing.

Color: White

This gearcase is the washer transmission assembly that transfers motor power to the agitator and spin basket, restoring proper agitation and spin for top-load washers. It replaces a worn or damaged gearbox to help get cycles working correctly. What it does:

• Converts motor rotation into the agitator and tub motion for wash and spin cycles
• Restores normal agitation when worn gears cause weak or no agitation
• Helps eliminate grinding, clunking, or abnormal noises from the washer drive area
• Supports proper spin operation when a failing gearbox prevents the tub from reaching speed

• Disconnect power and water before beginning service.
• Service typically requires tub/cabinet disassembly and removal of the old gearcase; follow the washer's service manual.
• Some applications may require new seals, gaskets, or fasteners.

Mixer not turning or making grinding noises? This gearcase assembly houses the planetary gears that drive your attachments. Moderate DIY repair.

This direct-drive gearcase converts the washer motor's power into the agitation and spin motions. Replacing a worn gearcase restores normal drive function so the washer can agitate and spin as intended. What it does

• Transfers motor rotation to the agitator and spin basket for wash and spin cycles
• Worn or damaged gear teeth can cause no agitation or no spin
• Damaged gearcase may produce loud grinding, clunking, or unusual noises during operation
• Failure can cause intermittent drive or loss of drive in one or both cycles

• Disconnect power and water before starting any repair to prevent shock or flooding
• Drain the washer and secure the tub/agitator before removing components
• May require removing the cabinet or access panels and supporting the drum during service

This is the gearcase that houses the internal gears responsible for transferring motor power to the mixing attachments in a stand mixer. It contains the gear train that controls speed and torque output. Replace this gearcase if you hear grinding noises, the mixer struggles under load, gears are visibly worn or stripped, or if lubricant is leaking from the housing.

This is the gearcase (gearbox) housing for a stand mixer, which contains and supports the internal gears that transfer motor power to the mixing attachments. It serves as the structural enclosure for the gear train assembly. Replace this part if the gearcase is cracked, leaking lubricant, or if the gears are no longer properly supported, causing unusual noises or wobbling during operation.

This pedestal feet assembly provides the lower support and leveling for a laundry pedestal, helping keep the pedestal stable and aligned beneath the washer or dryer. Designed to restore proper support and reduce rocking. What it does:

• Replaces damaged or worn pedestal feet that cause rocking, uneven height, or instability
• Provides adjustable support to help level the pedestal on uneven floors
• Protects floors by maintaining proper pedestal alignment and preventing scraping
• Restores safe, secure support for appliances installed on the pedestal

• Follow the appliance and pedestal manufacturer instructions; have a second person or proper support to prevent tip-over when removing or installing the pedestal
• Ensure the appliance is powered off and disconnected from utilities if appliance removal or repositioning is required
• Use basic hand tools; confirm all fasteners are tightened securely after installation

This pedestle is the replacement agitator post that supports and centers the washer agitator, restoring proper agitation and load stability for top-load washers. It's a direct-fit part used during agitator assembly repairs. What it does:

• Centers and secures the agitator on the transmission shaft for effective wash action
• Helps transmit agitation motion from the transmission to the agitator
• Commonly replaced when the agitator wobbles, slips, or does not rotate properly
• Restores stable operation without requiring a full agitator or transmission replacement

• One pedestle (agitator post) as shown

• Disconnect power to the washer before beginning any repair
• Remove agitator per manufacturer instructions to access and replace the pedestle
• Use appropriate hand tools; keep fasteners organized for reassembly