Columbia Log Splitter Parts

This is a genuine OEM clamp sourced directly from the manufacturer. It is used in various lawn and garden machines to connect hoses to fittings. It is used to connect piping to water pumps, exhaust pipes to exhaust manifolds, and other similar applications. This connection prevents fluids or air from leaking from the hose. Clamps may be spring or screw/band clamps. Spring clamps require no tools to install and remove; however, the size must be more accurate than when using screw/band clamps. Screw/band clamps are adjustable and can be tightened or loosened. Screw clamps should be inspected periodically to ensure tightness and that the clamps have not rusted.Hose clamps are installed approximately 1/4 inch below the end of the hose. If two clamps are used, there should be 1/4 inch between the two bands. When using a screw clamp, loosen the screw with a screwdriver just enough to fit the clamp over the hose. If using a spring clamp, squeeze the clamp and hold it open. Slide the clamp over the hose and then attach the hose and clamp to the fitting. Slide the clamp into place at the joint and tighten. Do not overtighten. This brass-colored clamp is a spring clamp made of metal; it is sold as an individual unit. This clamp is compatible with many different types of pipes made by various manufacturers.

Exhaust piping connects to the muffler system on small engines. Replace if cracked, corroded, or damaged to restore proper exhaust routing and function.

Cylinder head assembly for small engines used in snow throwers and log splitters. Replaces cracked, warped, or damaged cylinder heads that compromise engine structure and seal integrity.

Seals the intake valve to prevent oil leaks and maintain proper compression in small engines. Replace if you notice oil consumption or performance loss.

Intake valve seal prevents air and fuel from escaping during engine operation. Replace if you notice oil consumption or reduced performance. Verify fit with your engine model number before ordering.

Fix engine starting problems or loss of compression with this valve spring. Controls valve timing in small engines. Common repair for lawn tractors and snow throwers.

This replacement part is an oil seal. This part is small but important in various types of machines that rely on oil to run. The oil seal is found near the fuel tank and ensures that there are no leaks. If the machine is leaking oil, it can be due to a damaged oil seal. Seals like this one can wear out over time or be knocked out of place by impact.This is a genuine OEM replacement part manufactured by MTD. This part is sold individually.

This choke control lever automatically regulates the combined amount of air and fuel that come together in a small gasoline powered engine's carburetor to give a cold engine a fuel-rich mixture when the motor is first started. The control lever has several positions that allow it to adjust the fuel/air mixture in lawn equipment such as lawn mowers, snow blowers, tillers, chippers, log splitters, and other small gas engines. Over time with regular use, the control lever may become worn and must be replaced. There are several signs that indicate a choke control lever may be failing. If the gas tank is full of fresh gasoline but the engine refuses to start, if the engine starts and quickly floods, or if the engine runs at top speed but does not idle, the choke control level may be need to be replaced. Should the choke control lever need to be replaced, it is essential to use an OEM genuine manufactured replacement part such as this one. OEM parts are built to the exact specifications of the equipment's original parts. This part is compatible with Huskee, Cub Cadet, Yard Man, MTD, Yard Machines, and Troy-Bilt brand equipment.

Cylinder head gaskets provide a seal between the engine block and the head that caps the cylinders. They ensure that the cylinders, oil, and cooling channels are isolated from one another and contain the pressure in the engine. If there is a problem with a gasket, it could result in overheating, white smoke from the exhaust, and leaks.The cylinder head gasket undergoes a lot of stress when the engine is running. Over time, the gasket can start to wear down, crack, and break. Owners will want to replace the gasket to ensure the machine is running properly and efficiently. Replacing the cylinder head gasket can be a large job even when working on a small engine.This cylinder head gasket is used in engines from a range of manufacturers including MTD, Craftsman, Columbia, Yard Machines, Cub Cadet, and Troy-Bilt. The gaskets are OEM parts sourced from the manufacturer. Each of the gaskets is sold individually.

Piston ring set for small engines. Installs between cylinder wall and piston to maintain gas compression. Replace if rings are worn or damaged.

Replacement fuel tank for small engines. Installs as the main fuel reservoir. Order a new tank if yours is cracked, leaking, damaged, or punctured.

This is an M5 x 8 bolt used in lawn equipment and other devices. It is typically used as a fastener on the top of the machine. Over time, the bolt may loosen and fall out. If the bolt is missing, it must be replaced for the equipment to continue to operate safely and efficiently.Before beginning a replacement, allow the engine to cool completely to prevent burns and other injuries. Wear protective gloves. If there is a damaged bolt, remove it before installing the new replacement part. Install the new bolt with a wrench or the appropriate sized socket. Secure tightly to ensure it stays fit.The M5 x 8 bolt is a genuine OEM replacement part. It is sold individually. The bolt is supplied by the manufacturer and made of high-quality, durable materials. It is compatible with machines from Troy-Bilt, Yard Machines, Cub Cadet, and MTD brand equipment. The bolt is usable in a variety of engines, including those found in tillers, blowers, chippers, log splitters, and other various lawn equipment types.

This is an M8 x 55 bolt typically used in small engines and lawn equipment. Due to regular wear and tear, bolts in lawn equipment may become lost or damaged over time. If the equipment is performing poorly, or vibrating excessively, a bolt may be the issue and replacement will be required.Be sure to wear gloves when replacing an M8 x 55 bolt. Allow the motor in your equipment to cool completely before disassembly. Once cooled, a damaged or missing bolt can be replaced using an appropriately sized wrench or socket set.The M8 x 55 bolt is an authentic OEM replacement part sourced directly from the manufacturer. It is sold individually. It is made of durable, high-quality material. The M8 x 55 bolt is used in various machines, including tillers, log splitters, chippers, and other small engines. The bolt is compatible with equipment made by Troy-Bilt, Yard Machines, Cub Cadet, and MTD.

Spider bushing bearing for log splitters. Replace when you notice excessive play, wobbling, or unusual noise during operation. Verify fit with your model.

Hydraulic inlet filter for log splitters. Filters contaminants from hydraulic fluid to protect pump and valves. Replace when clogged or annually. Confirm fit with your model number.