Parts for Bosch B18IF800SP/02: Compressor Parts

Removes impurities from your refrigerator's water and ice supply. Replace every 6 months for clean, fresh-tasting water. Verify fit by model number.

This is a filter drier used in the sealed refrigeration system to remove moisture and contaminants from the refrigerant lines. It is a small cylindrical component typically located along the refrigerant tubing between the condenser and the capillary tube. Replace this part if the refrigerator or freezer is not cooling properly due to a restricted or saturated drier, typically during a sealed system repair.

Refrigerator not cooling or running constantly? This compressor powers your cooling system. Advanced repair requiring refrigerant handling expertise.

This replacement top lid restores the appliance's sealed cover and appearance while protecting internal components from debris and moisture. It fits where the original top cover was damaged, cracked, or cosmetically worn. What it does:

• Replaces a cracked, warped, or broken top cover to protect internal parts
• Helps keep dust, water splashes, and debris out of the appliance interior
• Restores a secure, flush top surface and original appearance
• Reduces risk of further damage from exposed components

• Disconnect power and water (if applicable) before starting any repair
• Basic hand tools are typically required; handle edges carefully to avoid scratches
• Inspect mounting points/hinges during install; reuse or replace fasteners as needed

This replacement top lid restores the appliance's sealed cover and appearance while protecting internal components from debris and moisture. It fits where the original top cover was damaged, cracked, or cosmetically worn. What it does:

• Replaces a cracked, warped, or broken top cover to protect internal parts
• Helps keep dust, water splashes, and debris out of the appliance interior
• Restores a secure, flush top surface and original appearance
• Reduces risk of further damage from exposed components

• Disconnect power and water (if applicable) before starting any repair
• Basic hand tools are typically required; handle edges carefully to avoid scratches
• Inspect mounting points/hinges during install; reuse or replace fasteners as needed

Power cord for refrigerators and freezers. Connects appliance to wall outlet. Replace if cord is frayed, damaged, cracked, or missing its prongs.

Condensate water container collects moisture from your refrigerator's cooling system. Replace if cracked, broken, or leaking to prevent water damage.

Removes impurities from your refrigerator's water and ice supply. Replace every 6 months for clean, fresh-tasting water. Verify fit by model number.

Freezer not cooling or won't start? This power module control board regulates electrical functions to restore reliable operation. Direct replacement.

Replace a cracked or missing housing cover that exposes internal components to debris and moisture. Restores proper sealing and component protection.

A replacement shock absorber that cushions and appliance component to reduce noise and stabilize movement for smoother, more controlled operation. Restores dampening to doors or tubs that close unevenly or vibrate. What it does:

• Dampens and slows movement to prevent slamming and reduce impact wear
• Stabilizes panels or tubs to cut down on vibration and rattling sounds
• Helps maintain even, controlled closing and opening motion
• Commonly used when a door feels loose, drops, or closes too quickly

• Disconnect power (and water if applicable) before attempting service
• Retain original mounting hardware; only replace items explicitly listed as included
• Ensure correct orientation and secure fasteners; test operation after installation

Mounting clip for refrigerator interior components. Secures shelves, bins, or panels in place. Replace if cracked, broken, or missing for proper fit.

Leveling foot installs at the refrigerator base to support and level the unit. Replace if worn, cracked, broken, or missing to restore stability.

Refrigerator not cooling or compressor not starting? This start relay controls the signal that initiates the compressor. Direct replacement part.

This is a small wheel designed for use in a refrigerator or freezer, typically mounted on a shelf, drawer, or rack to allow smooth sliding in and out. It helps support the weight of stored items while enabling easy access. Replace this wheel if it is cracked, broken, or no longer rolling freely, causing drawers or racks to stick or sit unevenly.

A replacement water inlet valve assembly that controls water entry to the appliance for proper fill cycles and normal operation. Restores reliable filling and helps stop unwanted leaks or no-fill conditions. What it does

• Opens and closes to let water into the unit during fill cycles.
• Helps maintain correct water level for washing and rinsing.
• Can stop water flow when the cycle is finished or if a fault is detected.
• Commonly associated with symptoms such as no water fill, slow fill, unit not starting due to low water, or visible leaks at the valve.

• Disconnect power and shut off the water supply before starting any repair.
• Handle electrical connections and hose fittings carefully; replace any damaged clamps or seals.

This cable connector is a replacement wire terminal used to restore a secure electrical connection in compatible Bosch appliances. It helps reestablish reliable power or signal continuity where a damaged or corroded connector causes intermittent or failed operation. What it does:

• Provides a secure electrical connection between wiring and appliance components
• Replaces damaged, corroded, or loose terminals that cause intermittent power or errors
• Helps prevent arcing and poor contact that can lead to component failure
• Suitable for repairs where the original connector is worn or physically broken

• Disconnect power before starting any repair to avoid shock or equipment damage
• Compare the replacement connector to the original for correct fit and orientation
• Use proper crimping or terminal tools if required; ensure a snug, strain-relieved connection

Secures the water filter in your refrigerator for a snug, leak-free fit. Replace if lost during filter changes, cracked, damaged, or worn out over time.

This is a housing component used inside the freezer section of the refrigerator. It serves as a protective enclosure for internal parts such as sensors, lights, or fan assemblies, helping to keep them properly positioned and shielded. Replace this housing if it is cracked, broken, or warped, which can affect the proper operation of the components it protects.

If your refrigerator cabinet feels warm or cooling is weak, the condenser fan may have failed. This fan circulates air over the condenser coil to remove heat.

This shock absorber cushions and controls dishwasher door movement to reduce slamming and improve closing action. It helps protect the door and cabinet from impact and can reduce noise during operation. What it does:

• Dampens and slows the dishwasher door as it opens and closes
• Helps prevent sudden drops or slamming that can damage the door or hinges
• Reduces vibration and noise caused by uncontrolled door movement
• Restores smoother, more controlled door operation when the original shock wears out

• One shock absorber

• Disconnect power to the appliance before beginning any repair
• Remove the dishwasher door panels or access panels to reach the mounting points
• Support the door during removal/installation to prevent it from falling or binding
• Use the OEM mounting hardware and verify secure attachment and correct alignment after installation

This is a small fixture component used to secure or position an interior shelf inside the refrigerator. It helps keep shelving properly aligned and stable within the cabinet. Replace this fixture if a shelf wobbles, tilts, or no longer stays in place due to a broken or missing mounting point.

Fixes incorrect temperature readings or frequent cycling. This thermistor monitors compartment temp for proper cooling. Moderate DIY repair, 30-45 minutes.

Base panel for upright freezers and wine coolers. Covers and protects the bottom exterior. Replace if cracked, damaged, or missing for a finished look.

Base panel for upright freezers. Covers and protects the bottom section of the unit. Replace if cracked, damaged, or missing to restore appearance.

This is a protective housing or case that encloses an internal component in a range or oven. It shields the enclosed part from heat, moisture, or physical damage during operation. Replace this housing if it is cracked, warped, or damaged, which could leave internal components exposed and vulnerable to malfunction.

Base panel for refrigerators and freezers. Covers the bottom front of the appliance. Replace if cracked, damaged, or missing to restore appearance.

Fix refrigerator control issues with this transformer. Restores proper voltage to electronic controls and display boards. Moderate DIY repair.

Fixes unresponsive controls, display errors, or cycle failures in refrigerators and freezers. Direct replacement for failed main control modules.

Adhesive mounting tape secures trim, wiring, and small components while reducing rattles and moisture intrusion. Replace when worn or loose. Verify fit with your model number before ordering.

Electronic power module for the dishwasher. This is the main control board that manages power and timing for wash, drain, and drying functions, helping restore normal operation when the original module has failed or is intermittent.

• Regulates incoming power and switches major loads (circulation pump, drain pump, heater, inlet valve)
• Coordinates cycle logic based on door and sensor inputs
• May help when the dishwasher won't power on or start a cycle
• May help when cycles stop mid-way, don't complete, or drying performance is poor

• Disconnect electrical power at the circuit breaker before servicing
• Access is typically from behind the lower toe panel/base; remove panels as needed
• Photograph and label wiring; transfer any mounting hardware; seat connectors fully
• Use ESD protection and handle the board by its edges only

Freezer won't start or stops mid-cycle? This control module manages cycle timing and user interface. Restores command functions when the board fails.