Parts for Bosch B30IR800SP/01: Compressor Parts

Fix a refrigerator that won't cool or runs constantly with a new compressor. This critical component circulates refrigerant to maintain proper temperatures.

Fixes unresponsive controls, display errors, or cycle failures in refrigerators and freezers. Direct replacement for failed main control modules.

Power cord for refrigerators and freezers. Connects appliance to wall outlet. Replace if cord is frayed, damaged, cracked, or missing its prongs.

Leveling foot installs at the refrigerator base to support and level the unit. Replace if worn, cracked, broken, or missing to restore stability.

Fix water dispenser not working or leaking with this outlet valve. Controls water flow from reservoir to dispenser. Moderate 30-45 minute repair.

Mounting clip for refrigerator interior components. Secures shelves, bins, or panels in place. Replace if cracked, broken, or missing for proper fit.

Fixes incorrect temperature readings or frequent cycling. This thermistor monitors compartment temp for proper cooling. Moderate DIY repair, 30-45 minutes.

This is a small wheel designed for use in a refrigerator or freezer, typically mounted on a shelf, drawer, or rack to allow smooth sliding in and out. It helps support the weight of stored items while enabling easy access. Replace this wheel if it is cracked, broken, or no longer rolling freely, causing drawers or racks to stick or sit unevenly.

Fix intermittent filling or valve clicking with this refrigerator valve magnet solenoid coil. Restores reliable valve actuation and water flow control.

This cable connector is a replacement wire terminal used to restore a secure electrical connection in compatible Bosch appliances. It helps reestablish reliable power or signal continuity where a damaged or corroded connector causes intermittent or failed operation. What it does:

• Provides a secure electrical connection between wiring and appliance components
• Replaces damaged, corroded, or loose terminals that cause intermittent power or errors
• Helps prevent arcing and poor contact that can lead to component failure
• Suitable for repairs where the original connector is worn or physically broken

• Disconnect power before starting any repair to avoid shock or equipment damage
• Compare the replacement connector to the original for correct fit and orientation
• Use proper crimping or terminal tools if required; ensure a snug, strain-relieved connection

Fix a refrigerator that won't start or run cycles with this power control board module. Restores electrical power to control electronics for reliable operation.

Replace a cracked or missing housing cover that exposes internal components to debris and moisture. Restores proper sealing and component protection.

This is a filter drier used in the sealed refrigeration system to remove moisture and contaminants from the refrigerant lines. It is a small cylindrical component typically located along the refrigerant tubing between the condenser and the capillary tube. Replace this part if the refrigerator or freezer is not cooling properly due to a restricted or saturated drier, typically during a sealed system repair.

This is a small fixture component used to secure or position an interior shelf inside the refrigerator. It helps keep shelving properly aligned and stable within the cabinet. Replace this fixture if a shelf wobbles, tilts, or no longer stays in place due to a broken or missing mounting point.

Base panel for refrigerator and freezer models. Replaces cracked, broken, or missing bottom panels. Restores structural integrity and appearance.

Replace your refrigerator's base panel if it's cracked, broken, or missing. This decorative trim covers the bottom front of your side-by-side unit.

Adhesive mounting tape secures trim, wiring, and small components while reducing rattles and moisture intrusion. Replace when worn or loose. Verify fit with your model number before ordering.

If your refrigerator cabinet feels warm or cooling is weak, the condenser fan may have failed. This fan circulates air over the condenser coil to remove heat.

This shock absorber cushions and controls dishwasher door movement to reduce slamming and improve closing action. It helps protect the door and cabinet from impact and can reduce noise during operation. What it does:

• Dampens and slows the dishwasher door as it opens and closes
• Helps prevent sudden drops or slamming that can damage the door or hinges
• Reduces vibration and noise caused by uncontrolled door movement
• Restores smoother, more controlled door operation when the original shock wears out

• One shock absorber

• Disconnect power to the appliance before beginning any repair
• Remove the dishwasher door panels or access panels to reach the mounting points
• Support the door during removal/installation to prevent it from falling or binding
• Use the OEM mounting hardware and verify secure attachment and correct alignment after installation

Condensate water container collects moisture from your refrigerator's cooling system. Replace if cracked, broken, or leaking to prevent water damage.

Base panel for refrigerators and freezers. Covers the bottom front of the appliance. Replace if cracked, damaged, or missing to restore appearance.

Condensate water container collects moisture from your refrigerator's cooling system. Replace if cracked, broken, or leaking to prevent water damage.

Fix refrigerator control issues with this transformer. Restores proper voltage to electronic controls and display boards. Moderate DIY repair.