Parts for Whirlpool GC900QPPB0: 04 - Container Parts

This replacement screw secures panels, brackets, and internal components inside your appliance to keep them aligned and rattle-free. Replace stripped, rusty, or missing hardware to restore a tight fit and dependable operation.

• Holds metal panels, brackets, ducts, or trim in place
• Helps maintain alignment and reduces vibration and noise
• Replaces missing, corroded, or stripped screws
• Common symptoms: loose panel or component, rattling/buzzing during use, screw won't tighten

• Disconnect power and shut off gas/water before servicing
• Start threads by hand to avoid cross-threading; use the correct driver
• Replace one fastener at a time to maintain alignment
• Tighten snugly—do not overtighten to prevent stripping

Replacement refrigerator door handle that restores a secure grip and proper door operation. Installs in place of a broken, cracked or loose handle to make opening and closing the fridge easier and safer. What it does:

• Replaces a damaged or cracked refrigerator door handle so the door can be opened and closed normally.
• Provides a secure gripping surface to reduce slipping and improve user control.
• Stops further damage to the door trim or mounting points caused by a worn, loose, or broken handle.
• Matches original mounting points on compatible appliances for a straightforward replacement.

• Read the appliance manufacturer's instructions before starting; keep original fasteners unless replacements are provided.
• Use basic hand tools; avoid forcing parts—inspecting mounting tabs can prevent additional damage.
• Disconnect power to the appliance before working near electrical components; if the door has integrated wiring (e.g., lights or dispensers), follow manufacturer safety guidance.

This replacement handle restores a secure, comfortable grip on your appliance's front panel, helping you open and close the door or drawer with confidence. It renews both function and appearance when the original handle is cracked or loose.

• Provides the leverage needed to open and close the door/drawer
• Direct replacement for a broken, cracked, worn, or wobbly handle
• Can help resolve difficulty pulling the panel open due to a loose handle
• Refreshes the appliance's exterior appearance

• Disconnect power before servicing
• Support the panel while removing the old handle to avoid stressing hinges
• Align the new handle and reuse the original mounting hardware/end caps as applicable; tighten evenly without overtightening
• Test for a secure fit and smooth operation

This replacement container front panel restores the front-facing surface of a refrigerator drawer or container, returning a finished appearance and protecting stored items. Available in matching white or black finishes for cosmetic repairs. What it does:

• Replaces a cracked, dented, or scratched drawer front to restore appearance and function
• Secures to the container/drawer to help keep contents enclosed and accessible
• Restores proper alignment and sealing where applicable for smooth drawer operation
• Useful when clips, tabs, or the original front are damaged from impact or wear

• Disconnect power to the appliance before beginning any repair to avoid injury.
• Remove the drawer or container per the appliance service instructions; some fasteners or retaining clips may need to be released.
• Handle the panel carefully to avoid scratching the finish; use appropriate trim tools to release clips if needed.

Size: 8-18 x 1/2 inch.

This door lock latch assembly secures the washer door during operation so cycles can run safely and water stays contained. It replaces a worn or damaged latch to restore proper door locking and cycle start. What it does

• Secures and locks the washer door during wash and spin cycles so the appliance can operate normally.
• Triggers the door-closed sensor/switch that allows the washer to start and continue a cycle.
• Helps prevent accidental door opening and reduces the risk of leaks during operation.
• Common symptoms indicating this part may be needed: washer won't start, door won't latch or lock, or the latch feels loose or broken.

• Always disconnect power to the appliance before inspecting or replacing the door lock latch.
• Handle the door and glass carefully to avoid damage; align the latch with the strike before tightening fasteners.
• After installation, test a short cycle (no clothes) to ensure the door locks and the washer starts properly.

Color: White

The Foot Pedal Kit is an OEM replacement part for Whirlpool trash compactors.

Causes can be attributed to stress fractures developing over years of repetitive flexing through thousands of compressions. Constant impact also accelerates the wear of plastic hinges and snap fittings.

Symptoms of a bad kit include:

• Pedal sticking, binding, or unresponsiveness during use
• Engaging the wrong compaction cycles
• Cracked or split pedal housing compromising sealing and durability
• Damaged connectors interrupting communication with the motor

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This safety switch actuator engages the door/interlock switch so the appliance senses a closed, secure door and will run as intended. Replacing a worn actuator restores reliable door engagement and control-system signaling. What it does:

• Moves the door latch into position to trip the appliance's safety/interlock switch
• Ensures the control board senses a closed door so cycles can start or continue
• Common symptom: appliance won't start or stops when the door is shut or nudged
• Common symptom: door won't fully latch or feels loose when closing

• One safety switch actuator

• Disconnect power (and water if applicable) before starting any repair
• Remove exterior panels or door assembly as needed to access the actuator; keep fasteners organized
• Verify switch alignment with the actuator and test operation before reassembly
• Wear gloves and eye protection

This container roller bearing supports the trash compactor drawer as it slides on its tracks. Replacing a worn bearing restores smooth, quiet movement and helps keep the container aligned for easy opening and closing.

• Provides low-friction support so the drawer glides smoothly on the tracks
• Helps maintain proper container alignment and stability
• Reduces squeaks, grinding, and sticking during operation
• Common symptoms: drawer hard to open/close, scraping noises, binding or uneven movement, visible wear/flat spots on the bearing

• Disconnect power to the compactor before servicing
• Remove and empty the drawer to access the bearing location
• Install the new bearing in the same orientation; transfer any hardware as needed
• Inspect rollers, axles, and tracks; replace any additional worn parts for best results

Size: 3\8-24 inch.

Fits 15 and 18 inch compactors. This kit is for securing the compactor bags. Kit contains a set of 4 buttons and screws.

Size: 8-32 x 3/8 inch.

This E-ring retaining clip secures latch components by locking onto a shaft or pin so the latch assembly stays in place. It's a small but essential metal clip that prevents latch parts from slipping off and causing door or panel issues. What it does:

• Locks onto latch shafts or pins to hold the latch assembly together
• Prevents the latch or related parts from sliding off during operation
• Common symptoms: door or panel won't stay closed, rattling or loose parts near the latch, visible clip missing or deformed
• Helps restore secure engagement of the latch when the clip is intact and correctly positioned

• One E-ring retaining clip

• Disconnect power or unplug the appliance before beginning any repair
• Use pliers or snap-ring tools to remove/install the clip; avoid excessive force that could deform it
• Replace the clip if it is bent, cracked, or worn — do not reuse a damaged clip

This is a replacement machine screw sized 8-18 x 3/8 that secures panels and components on compatible appliances. It restores proper fastening where a worn, stripped, or missing screw causes loose parts or rattling. What it does

• Fastens control panels, trim pieces, or brackets to the appliance chassis
• Replaces stripped, corroded, or missing screws that cause loose panels or vibrating noise
• Provides correct thread engagement for a secure hold in tapped holes
• Small hardware solution often used during door, console, or interior repairs

• One 8-18 x 3/8 machine screw (quantity: 1)

• Use the correct screw size and thread; do not force a different-size fastener into tapped holes
• Hand-start the screw to avoid cross-threading, then tighten with the appropriate screwdriver
• Disconnect power before accessing internal components or panels on electrical appliances
• If metal threads are damaged, repair with a helicoil or replace the damaged component rather than over-torquing

This latch plate secures the appliance door to the cabinet, providing the positive engagement needed for proper door closure and operation. It helps restore a door that won't stay closed or won't trigger door switches. What it does:

• Acts as the door strike that the latch engages to hold the door shut
• Ensures the door closes firmly so door switches can register a closed state
• Can stop issues like a loose or misaligned door, or a door that won't remain closed
• Restores proper alignment and engagement without replacing the full latch assembly

• Disconnect power (and gas if applicable) before servicing
• Remove the door or access panel to reach the latch area
• Inspect related latch components and alignment; replace only the damaged part
• Use basic hand tools; tighten fasteners securely but avoid overtightening

Size: 8 x 1/2 ab.