Parts for Whirlpool GC900QPPQ1: 04 - Container Parts

This replacement screw secures panels, brackets, and internal components inside your appliance to keep them aligned and rattle-free. Replace stripped, rusty, or missing hardware to restore a tight fit and dependable operation.

• Holds metal panels, brackets, ducts, or trim in place
• Helps maintain alignment and reduces vibration and noise
• Replaces missing, corroded, or stripped screws
• Common symptoms: loose panel or component, rattling/buzzing during use, screw won't tighten

• Disconnect power and shut off gas/water before servicing
• Start threads by hand to avoid cross-threading; use the correct driver
• Replace one fastener at a time to maintain alignment
• Tighten snugly—do not overtighten to prevent stripping

Replacement refrigerator door handle that restores a secure grip and proper door operation. Installs in place of a broken, cracked or loose handle to make opening and closing the fridge easier and safer. What it does:

• Replaces a damaged or cracked refrigerator door handle so the door can be opened and closed normally.
• Provides a secure gripping surface to reduce slipping and improve user control.
• Stops further damage to the door trim or mounting points caused by a worn, loose, or broken handle.
• Matches original mounting points on compatible appliances for a straightforward replacement.

• Read the appliance manufacturer's instructions before starting; keep original fasteners unless replacements are provided.
• Use basic hand tools; avoid forcing parts—inspecting mounting tabs can prevent additional damage.
• Disconnect power to the appliance before working near electrical components; if the door has integrated wiring (e.g., lights or dispensers), follow manufacturer safety guidance.

This replacement handle restores a secure, comfortable grip on your appliance's front panel, helping you open and close the door or drawer with confidence. It renews both function and appearance when the original handle is cracked or loose.

• Provides the leverage needed to open and close the door/drawer
• Direct replacement for a broken, cracked, worn, or wobbly handle
• Can help resolve difficulty pulling the panel open due to a loose handle
• Refreshes the appliance's exterior appearance

• Disconnect power before servicing
• Support the panel while removing the old handle to avoid stressing hinges
• Align the new handle and reuse the original mounting hardware/end caps as applicable; tighten evenly without overtightening
• Test for a secure fit and smooth operation

White front container panel for trash compactors. Replaces scratched, chipped, or discolored panels on the compactor container exterior. Restores appearance.

Size: 8-18 x 1/2 inch.

This door lock latch assembly secures the washer door during operation so cycles can run safely and water stays contained. It replaces a worn or damaged latch to restore proper door locking and cycle start. What it does

• Secures and locks the washer door during wash and spin cycles so the appliance can operate normally.
• Triggers the door-closed sensor/switch that allows the washer to start and continue a cycle.
• Helps prevent accidental door opening and reduces the risk of leaks during operation.
• Common symptoms indicating this part may be needed: washer won't start, door won't latch or lock, or the latch feels loose or broken.

• Always disconnect power to the appliance before inspecting or replacing the door lock latch.
• Handle the door and glass carefully to avoid damage; align the latch with the strike before tightening fasteners.
• After installation, test a short cycle (no clothes) to ensure the door locks and the washer starts properly.

White plastic foot pedal for trash compactors. Installs at base of unit to release door latch. Replace if cracked, broken, or no longer springs back.

Replacement foot pedal for trash compactors. Installs at the base to operate the door release mechanism. Replace if cracked, broken, or missing.

Compactor won't run unless you hold the dial? A worn safety switch actuator prevents proper door latch engagement. This repair restores automatic operation.

Replacement roller bearing for trash compactor drawers. Installs on tracks to support smooth gliding. Replace worn or damaged bearings for easier operation.

Size: 3\8-24 inch.

Fits 15 and 18 inch compactors. This kit is for securing the compactor bags. Kit contains a set of 4 buttons and screws.

Size: 8-32 x 3/8 inch.

This latch pin secures the door latch mechanism on your trash compactor. Replace if the pin is broken, worn, or missing to restore proper door latching.

Latch spring for trash compactors. Installs in the door latch mechanism to provide tension. Replace if cracked, broken, or missing to restore proper latch function.

Compactor door won't latch or latch feels loose? This E-ring retaining clip secures latch components to the shaft. Quick 5-minute fix for latch problems.

Replace worn, stripped, or missing 8-18 x 3/8 machine screws that secure control panels, trim pieces, and brackets on your appliance. Restores tight fit.

Door strike plate for trash compactors. Mounts to cabinet frame to secure the door latch. Replace if cracked, bent, or missing to restore proper closure.

Protective guard for trash compactors. Shields internal components from debris and impact. Replace if cracked, broken, or missing to maintain proper function.

Front guard plate for trash compactors. Protects the compactor front panel from damage. Replace if cracked, torn, or worn to restore appearance.

Replacement fastener screw for appliances. Secures panels, trim, clips, and components. Needed when original screws are stripped, missing, or damaged.