Parts for Whirlpool TF8600XTP1: 05 - Container Parts

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This part has been discontinued by the manufacturer and is no longer available.

Color: Black & almond.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This door lock latch assembly secures the washer door during operation so cycles can run safely and water stays contained. It replaces a worn or damaged latch to restore proper door locking and cycle start. What it does

• Secures and locks the washer door during wash and spin cycles so the appliance can operate normally.
• Triggers the door-closed sensor/switch that allows the washer to start and continue a cycle.
• Helps prevent accidental door opening and reduces the risk of leaks during operation.
• Common symptoms indicating this part may be needed: washer won't start, door won't latch or lock, or the latch feels loose or broken.

• Always disconnect power to the appliance before inspecting or replacing the door lock latch.
• Handle the door and glass carefully to avoid damage; align the latch with the strike before tightening fasteners.
• After installation, test a short cycle (no clothes) to ensure the door locks and the washer starts properly.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

The Compactor Bag Caddy is an OEM component specifically designed for Whirlpool trash compactors. This caddy holds trash compactor bags securely in place during the compaction process. It measures about 8 inches wide by 16 inches high by 11 inches deep.

Symptoms of a bad compactor bag caddy include: 

• Bags not fitting, sliding, or twisting improperly during use
• Reduced internal storage volume within the compactor unit
• Difficulty removing full bags after compaction cycles  

Causes of failure can be cracks or breaks from repeated insertion/removal of bags over time, damage inhibiting bags from seating fully, or issues affecting durability.

This part is also compatible with garbage disposals and compactors from Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore brands.

This part has been discontinued by the manufacturer and is no longer available.

The Foot Pedal Kit is an OEM replacement part for Whirlpool trash compactors.

Causes can be attributed to stress fractures developing over years of repetitive flexing through thousands of compressions. Constant impact also accelerates the wear of plastic hinges and snap fittings.

Symptoms of a bad kit include:

• Pedal sticking, binding, or unresponsiveness during use
• Engaging the wrong compaction cycles
• Cracked or split pedal housing compromising sealing and durability
• Damaged connectors interrupting communication with the motor

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This safety switch actuator engages the door/interlock switch so the appliance senses a closed, secure door and will run as intended. Replacing a worn actuator restores reliable door engagement and control-system signaling. What it does:

• Moves the door latch into position to trip the appliance's safety/interlock switch
• Ensures the control board senses a closed door so cycles can start or continue
• Common symptom: appliance won't start or stops when the door is shut or nudged
• Common symptom: door won't fully latch or feels loose when closing

• One safety switch actuator

• Disconnect power (and water if applicable) before starting any repair
• Remove exterior panels or door assembly as needed to access the actuator; keep fasteners organized
• Verify switch alignment with the actuator and test operation before reassembly
• Wear gloves and eye protection

This container roller bearing supports the trash compactor drawer as it slides on its tracks. Replacing a worn bearing restores smooth, quiet movement and helps keep the container aligned for easy opening and closing.

• Provides low-friction support so the drawer glides smoothly on the tracks
• Helps maintain proper container alignment and stability
• Reduces squeaks, grinding, and sticking during operation
• Common symptoms: drawer hard to open/close, scraping noises, binding or uneven movement, visible wear/flat spots on the bearing

• Disconnect power to the compactor before servicing
• Remove and empty the drawer to access the bearing location
• Install the new bearing in the same orientation; transfer any hardware as needed
• Inspect rollers, axles, and tracks; replace any additional worn parts for best results

Size: 3\8-24 inch.

Size: 8-32 x 3/8 inch.

This E-ring retaining clip secures latch components by locking onto a shaft or pin so the latch assembly stays in place. It's a small but essential metal clip that prevents latch parts from slipping off and causing door or panel issues. What it does:

• Locks onto latch shafts or pins to hold the latch assembly together
• Prevents the latch or related parts from sliding off during operation
• Common symptoms: door or panel won't stay closed, rattling or loose parts near the latch, visible clip missing or deformed
• Helps restore secure engagement of the latch when the clip is intact and correctly positioned

• One E-ring retaining clip

• Disconnect power or unplug the appliance before beginning any repair
• Use pliers or snap-ring tools to remove/install the clip; avoid excessive force that could deform it
• Replace the clip if it is bent, cracked, or worn — do not reuse a damaged clip

This latch plate secures the appliance door to the cabinet, providing the positive engagement needed for proper door closure and operation. It helps restore a door that won't stay closed or won't trigger door switches. What it does:

• Acts as the door strike that the latch engages to hold the door shut
• Ensures the door closes firmly so door switches can register a closed state
• Can stop issues like a loose or misaligned door, or a door that won't remain closed
• Restores proper alignment and engagement without replacing the full latch assembly

• Disconnect power (and gas if applicable) before servicing
• Remove the door or access panel to reach the latch area
• Inspect related latch components and alignment; replace only the damaged part
• Use basic hand tools; tighten fasteners securely but avoid overtightening

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Bag carrier handle assembly that secures a disposable dust bag to the vacuum housing, letting you remove and replace bags cleanly and safely. Restores proper bag seating and handling for bagged vacuum units. What it does:

• Holds the dust bag in place so debris is directed into the bag, not the housing
• Provides a grip for removing and carrying full bags without tearing or spillage
• Replaces a cracked, broken, loose, or missing handle that prevents proper bag seating
• Helps stop bag detachment or leaks caused by an unstable carrier

• Always unplug the appliance before servicing.
• Remove the old bag and carrier, noting orientation; the carrier may snap into place or be secured with small screws.
• Verify the new carrier seats and latches fully before installing a new bag.

Rubber bumper for door/drawer.