Parts for Whirlpool TU950QPXS3: Container Parts

This is a replacement machine screw sized 8-18 x 3/8 that secures panels and components on compatible appliances. It restores proper fastening where a worn, stripped, or missing screw causes loose parts or rattling. What it does

• Fastens control panels, trim pieces, or brackets to the appliance chassis
• Replaces stripped, corroded, or missing screws that cause loose panels or vibrating noise
• Provides correct thread engagement for a secure hold in tapped holes
• Small hardware solution often used during door, console, or interior repairs

• One 8-18 x 3/8 machine screw (quantity: 1)

• Use the correct screw size and thread; do not force a different-size fastener into tapped holes
• Hand-start the screw to avoid cross-threading, then tighten with the appropriate screwdriver
• Disconnect power before accessing internal components or panels on electrical appliances
• If metal threads are damaged, repair with a helicoil or replace the damaged component rather than over-torquing

This actuator is the small mechanism that drives the dishwasher's detergent dispenser door, releasing detergent at the correct time in the cycle for consistent cleaning performance. What it does:

• Converts a control signal into movement to open the dispenser door
• Helps ensure detergent is released at the proper stage of the wash
• Wear or breakage can leave the cup closed or only partially opened
• Common symptoms: detergent left in cup after cycle, dispenser door not opening, or visible damage to the lever

• 1 actuator

• Disconnect power at the breaker before servicing
• Open the door and remove the inner door panel to access the dispenser assembly
• Note the actuator's orientation; transfer and seat it fully in the mechanism
• Reassemble the door, restore power, and run a short cycle to confirm proper dispenser operation

This stainless-steel control panel restores the front console finish and provides the mounting surface for the range's controls. It replaces a scratched, dented or damaged panel so buttons and displays mount securely and the appliance looks finished. What it does:

• Provides the exterior mounting surface for the console controls and display
• Restores a clean, undamaged front finish when the original panel is dented, scratched, or bent
• Keeps control components aligned and secured to prevent loose or misaligned buttons
• Helps protect internal control components from direct contact and debris

• Disconnect power to the appliance before starting any repair
• Typical install requires removal of trim/console screws and careful lifting of the old panel
• Handle the panel carefully to avoid new scratches; use appropriate hand tools and protect nearby surfaces
• If wiring or control modules need to be moved, note their positions or take photos before removal

This replacement container restores a secure, factory-fit compartment in your appliance. Install a new container when the original is cracked or broken to keep contents properly held and nearby parts aligned as designed.

• Provides the designated compartment to hold contents securely
• Interfaces correctly with its mounting points, guides, or adjoining parts
• Replaces cracked, warped, or broken containers that won't stay seated
• Helps prevent spills, jams, or interference with nearby components

• Disconnect power to the appliance; shut off water supply if applicable
• Wear cut-resistant gloves—damaged plastic edges can be sharp
• Move any screws, covers, or inserts from the old part to the new one
• Align tabs, tracks, or snaps and press into place without forcing

This door lock latch assembly secures the washer door during operation so cycles can run safely and water stays contained. It replaces a worn or damaged latch to restore proper door locking and cycle start. What it does

• Secures and locks the washer door during wash and spin cycles so the appliance can operate normally.
• Triggers the door-closed sensor/switch that allows the washer to start and continue a cycle.
• Helps prevent accidental door opening and reduces the risk of leaks during operation.
• Common symptoms indicating this part may be needed: washer won't start, door won't latch or lock, or the latch feels loose or broken.

• Always disconnect power to the appliance before inspecting or replacing the door lock latch.
• Handle the door and glass carefully to avoid damage; align the latch with the strike before tightening fasteners.
• After installation, test a short cycle (no clothes) to ensure the door locks and the washer starts properly.

This safety switch actuator engages the door/interlock switch so the appliance senses a closed, secure door and will run as intended. Replacing a worn actuator restores reliable door engagement and control-system signaling. What it does:

• Moves the door latch into position to trip the appliance's safety/interlock switch
• Ensures the control board senses a closed door so cycles can start or continue
• Common symptom: appliance won't start or stops when the door is shut or nudged
• Common symptom: door won't fully latch or feels loose when closing

• One safety switch actuator

• Disconnect power (and water if applicable) before starting any repair
• Remove exterior panels or door assembly as needed to access the actuator; keep fasteners organized
• Verify switch alignment with the actuator and test operation before reassembly
• Wear gloves and eye protection

This replacement refrigerator door handle provides a secure grip and restores proper opening and closing of the appliance door. Designed to match the original fit and finish for a clean, factory look. What it does:

• Replaces a cracked, broken or missing refrigerator door handle
• Restores a solid grip so the door opens and closes normally
• Prevents further damage from using makeshift grips or tape
• Helps keep the door aligned and sealed by providing proper leverage

• Disconnect power to the appliance or unplug the unit before starting work to avoid electrical hazard.
• Remove food and shelves from the door as needed for access and to prevent breakage.
• Use the correct screwdriver or socket to remove mounting screws; support the handle during removal and installation.
• If the handle attaches with hidden clips, work carefully to avoid breaking plastic retainers.

Size: 8-18 x 1/2 inch.

Size: 8 x 1/2 ab.

This container roller bearing supports the trash compactor drawer as it slides on its tracks. Replacing a worn bearing restores smooth, quiet movement and helps keep the container aligned for easy opening and closing.

• Provides low-friction support so the drawer glides smoothly on the tracks
• Helps maintain proper container alignment and stability
• Reduces squeaks, grinding, and sticking during operation
• Common symptoms: drawer hard to open/close, scraping noises, binding or uneven movement, visible wear/flat spots on the bearing

• Disconnect power to the compactor before servicing
• Remove and empty the drawer to access the bearing location
• Install the new bearing in the same orientation; transfer any hardware as needed
• Inspect rollers, axles, and tracks; replace any additional worn parts for best results

Fits 15 and 18 inch compactors. This kit is for securing the compactor bags. Kit contains a set of 4 buttons and screws.

The Screw is an OEM part for Whirlpool refrigerators. This screw secures the refrigerator door hinge in place, allowing the door operates smoothly and seals properly. 

Over time, screws can become loose or go missing during repairs or adjustments, which can lead to a misaligned door, compromised sealing, and increased energy consumption. 

Symptoms of a bad screw include:

• The refrigerator door seems misaligned or does not close properly.
• Increased effort needed to open or close the door.
• Unusual gaps around the door seal when closed.
• The door might squeak or make other noises during operation.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.