Parts for Ge JGB660DP1BB: Control Panel & Cooktop Parts

Replace your gas range control knob if cracked, broken, or worn from frequent use. Installs on the control panel to operate burners and adjust flames.

This wire tie secures and organizes wiring inside the appliance to help prevent chafing and loose connections. Its 7-7/8 inch length is suited for bundling harnesses and routing cables away from heat and moving parts. What it does:

• Fastens and groups wires or small hoses to keep them neatly routed
• Helps prevent wire chafing, abrasion, and contact with sharp edges
• Reduces the chance of intermittent connections from loose wiring
• Keeps wiring away from moving components to reduce noise and wear

• Disconnect power before servicing the appliance
• Position wiring as needed, insert tie and tighten; avoid over-tightening
• Trim excess tie length flush and secure cut end away from wires
• Replace any damaged wiring insulation and verify routing before restoring power

Replacement end support for gas ranges. Provides structural support at the side of the range. Replace if cracked, bent, broken, or missing.

Left front end support bracket for gas ranges. Secures the front corner of the cooktop frame. Replace if cracked, bent, or missing to restore stability.

This RC19 electronic control is the user interface and control board that manages oven functions and timing. A flashed unit arrives pre-programmed to match the oven's control settings to restore normal operation. What it does:

• Replaces a failed

Replacement grate assembly for gas range stovetops. Provides stable cooking surface over burners. Order if your existing grate is cracked, broken, or worn.

Fixes unstable or uneven cooktop and misaligned burners. This rangetop and bracket assembly secures the cooktop to the frame for safe cooking.

This factory fastener secures internal components or panels in your appliance. Replacing a missing or stripped screw restores a snug fit, helps prevent vibration or rattling, and keeps assemblies aligned for proper operation.

• Secures brackets, p

Replaces worn, faded, or damaged control panel overlay. Restores button labels and console appearance. Installs over the control surface.

Medium burner cap for gas cooktops and ranges. Sits atop the burner head to distribute flame evenly. Replace if cracked, chipped, or worn from use.

Burner cap covers the burner head and distributes flame evenly on gas ranges and cooktops. Replace if cracked, warped, or missing for proper cooking.

Replacement burner cap for gas cooktops and ranges. Sits atop the burner head to distribute flame evenly. Replace if cracked, chipped, or worn.

Burner cap assembly covers the burner head on gas cooktops and ranges. Replace cracked, stained, corroded, or missing caps to restore appearance.

Replacement small surface burner for gas ranges and cooktops. Restores proper flame control when original burner is damaged, cracked, or corroded.

The Burner, Large V2 is an OEM part for GE gas ranges. It is designed to provide a consistent and even flame for cooking, ensuring efficient heat distribution for large pots and pans.

Causes of a bad burner can include clogging from food spills

Replacement burner head for gas ranges and cooktops. Installs on stovetop to distribute flame evenly. Replace if warped, cracked, or causing uneven flames.

Oval burner assembly for gas range cooktops. Replace if your burner head or cap is cracked, clogged, damaged, or missing. Includes both burner and cap.

Medium-sized surface burner for gas cooktops and ranges. Installs on the cooktop surface. Replace if cracked, worn, or providing uneven heat distribution.

If your gas range burner won't light or clicks continuously, this igniter clip secures the ignition system. Simple DIY fix in under 15 minutes.

A replacement ground harness that restores the appliance's chassis grounding connection to help ensure safe electrical operation. Installs quickly to replace a damaged or corroded ground lead and reduce risk of arcing. What it does

• Provides the dedicated chassis ground connection between appliance wiring and the cabinet
• Restores proper grounding when original harness is broken, frayed, corroded, or detached
• Helps prevent intermittent power issues, arcing, or nuisance tripping caused by poor ground continuity
• Used wherever a short ground lead or bonded connector is required for safety

• One ground harness as shown

• Disconnect power (unplug or shut off circuit breaker) before starting any repair
• Verify correct grounding point on the cabinet and secure the harness with the original screw or fastener
• Match connectors and routing to the original harness; avoid touching energized terminals during installation

Panel mounting screw secures trim, bezels, and internal components on ranges and cooktops. Replace when stripped, corroded, or missing to restore fit.

Protective bumper that cushions the burner grate and prevents scratching or denting the cooktop surface. Replace if cracked, worn, or missing.

Insulation shield that installs behind the range control panel. Protects control board and wiring from oven heat. Replace if cracked, damaged, or missing.

This is the flat griddle plate that sits over the center burners on compatible cooktops/ranges. It provides an even cooking surface for pancakes, sandwiches, and more, and replaces a worn or missing griddle so heat is distributed properly.

• Creat

This master wiring harness routes power and signals between the appliance's control components and electrical devices, restoring reliable electrical connections and proper operation. It replaces a damaged or corroded factory harness to help resolve intermittent power, control, or component failures. What it does:

• Carries power and signal connections between the control board and major electrical components
• Replaces burned, brittle, or frayed wiring that can cause intermittent operation or component failures
• Restores secure connector fits to prevent arcing or lost circuits
• Helps address symptoms such as no power to components, erratic control behavior, or visible wiring damage

• Always disconnect power (unplug or switch off breaker) before starting service
• Match connectors and routing to the original harness; avoid pinching or sharp bends
• Inspect mating connectors and terminals; replace if corroded or damaged