Parts for Ge JB480DY1WW: Control Panel & Cooktop Parts

This replacement control knob fits the surface burner valve on many ranges and cooktops. It restores smooth on/off operation and flame adjustment when the original knob is cracked, stripped, wobbly, or missing.

• Press-fits onto the valve stem to turn the surface burner on/off and set flame level
• Replaces knobs that are cracked, stripped (spins or slips), loose, melted, or missing
• Helps restore accurate feel and alignment so settings match the dial
• Common signs: knob rotates without engaging the valve or does not stay seated

• Ensure all burners are off and the appliance is cool before servicing
• Pull the old knob straight off the valve stem; do not pry against the control panel
• Align the new knob with the stem flats/notch and press firmly until fully seated
• If the knob won't seat, inspect the stem for debris or damage before reattempting

Fix a burner that won't heat, stays on high, or won't shut off by replacing the infinite switch. Controls surface element power at your selected setting.

Burner stuck on high or not heating? This infinite switch regulates cooktop burner power. Typical DIY repair takes about 30 minutes with basic tools.

Pilot indicator light mounts in the control panel and illuminates when a surface element or heating circuit is powered. Replace if burned out or stuck on.

Wiring harness for electric range pilot light indicator. Replace when control panel light fails or flickers. Verify fit with your model number.

Range won't complete self-clean cycle or overheats? This thermostat monitors oven temperature during cleaning and cuts power if overheating occurs.

This carton cover thermostat senses and controls temperature at the refrigerator/freezer carton cover to help maintain proper cooling function. It replaces a failed or intermittent thermostat to restore correct temperature regulation. What it does:

• Detects temperature near the carton cover and signals the control to start or stop cooling
• Helps prevent over-cooling or under-cooling in the compartment when functioning correctly
• Commonly diagnosed when temperature is inconsistent, compartment is too warm, or cooling cycles irregularly
• Matches the OEM mounting and connector style for direct replacement

• Disconnect power to the appliance before servicing to avoid electrical shock
• Access usually requires removing interior panels or the carton cover; keep fasteners for reassembly
• Handle the thermostat and sensor lead carefully to avoid damage; route wires clear of moving parts

Replacement mounting screw that secures the thermostat assembly to your range cabinet. Replace if stripped, missing, or damaged during repair work.

Fix unresponsive or intermittent range controls with this sealed rocker switch. Restores reliable on/off operation for panel buttons and switches.

This Haliant 6" heating element replaces a damaged or worn oven element to restore proper cooking and baking performance. It provides the heating surface needed for even temperature recovery and consistent results. What it does:

• Heats during bake/broil cycles to generate oven cooking temperatures
• Restores heat when a failed element causes little or no oven heat
• Helps correct uneven cooking or long preheat times caused by element failure
• Matches the OEM Haliant design for fit and function when compatible

• Disconnect power to the appliance before servicing to avoid shock
• Allow the appliance to cool fully before touching the element or inside surfaces
• Replace using proper mounting hardware and electrical connections; ensure secure, tight terminal connections

Replace a failed 8-inch radiant surface element when your burner won't heat. Restores proper heating response. DIY-friendly with basic tools.

Secures the radiant cooktop element in proper position. Replace if bracket is bent, broken, or missing to restore safe element support and alignment.

Fix a loose or sagging control panel with this range control bracket. Secures the control assembly to the frame for stable button operation. Easy install.

Self-clean cycle won't start or complete? This timer assembly controls oven cleaning cycles and basic timing functions on electric ranges.

Covers and protects the indicator lamp opening on your range control panel. Replace when cracked, discolored, or missing to restore visibility. Confirm fit with your model number.

Replacement mounting screw secures panels, brackets, and trim on ranges and cooktops. Install to replace missing, stripped, or rusted fasteners.

Can't adjust oven temperature? This range thermostat knob assembly restores precise temperature control. Fixes worn or broken control knobs on electric ranges.