Parts for Ge JBS15M2BB: 01 - Control Panel & Cooktop Parts

Replace a cracked, broken, or missing control knob on your range. This knob installs on the control shaft to restore precise dial adjustments.

Burner stuck on high or not heating? This infinite switch regulates cooktop burner power. Typical DIY repair takes about 30 minutes with basic tools.

Fixes burner stuck on high or no heat issues. This infinite switch regulates cooktop element temperature by cycling power on and off. Simple replacement.

Indicator light that illuminates when burners or oven are active. Replace if it stays on constantly or fails to light. Verify fit with your model number.

Protective cover that houses the temperature-sensing thermostat on your electric range. Replace if cracked, broken, or missing to protect internal components.

This thermostat is the oven's temperature control. It senses cavity temperature and switches the heat on and off to maintain your set temperature, helping your range bake and roast more consistently.

• Regulates oven temperature by opening/closing

Color: Black

End support cap for gas ranges. Installs on the side panel to provide structural support and a finished appearance. Replace if cracked or missing.

Right end support cap for gas ranges. Secures and covers the side panel edge. Replace if cracked, broken, or missing to restore a finished appearance.

This left-side cooktop bracket secures the cooktop to the range frame, restoring a solid, stable fit and preventing movement or misalignment. Durable stamped metal bracket designed to replace a worn or damaged mounting point. What it does:

• Anchors the left side of the cooktop to the range frame so the cooktop sits flush and stable
• Stops rocking, shifting, or gaps between the cooktop and the range while using the appliance
• Restores proper alignment after impact or corrosion of the original bracket

• One left-side cooktop mounting bracket

• Disconnect power to the appliance before beginning any repair
• Remove the cooktop or control panel per service instructions to access the bracket
• Use basic hand tools; replace only the damaged bracket and retain original fasteners unless corroded
• Tighten fasteners snugly but avoid over-torquing to prevent striping or damage

This trim control is a decorative trim piece that restores the finished look around the appliance control area and helps cover gaps where the control assembly meets the cabinet. It improves appearance and helps reduce dirt buildup. What it does:

• Covers and finishes the edge around the control area for a clean look
• Secures and conceals the control assembly for a factory appearance
• Helps prevent dirt and debris from collecting in the gap around controls
• Commonly replaced when cracked, chipped, warped, or missing

• Disconnect power to the appliance before starting any work.
• Remove any adjacent panels or bezels per the appliance service instructions to access the trim.
• Handle trim carefully to avoid cracking; use appropriate non-marring tools.

Secures components to your appliance chassis for a rattle-free fit. Replace missing, stripped, or corroded screws to keep panels and brackets aligned.

This pin locator secures a hinge or shaft pin in place to keep linked appliance components aligned and operating smoothly. It's a small replacement part that restores proper positioning where a locating clip or retainer is used. What it does

• Holds a hinge, shaft, or pivot pin in place to prevent lateral movement
• Restores proper alignment of doors, panels, or linked components
• Helps stop rattling, misalignment, or binding caused by a worn or missing locator
• Works as a direct replacement for the same OEM-labeled locating clip/retainer

• One pin locator

• High-level replacement; basic hand tools usually required
• Disconnect power (and water, if applicable) before servicing appliances with electrical components
• Keep track of small parts and orientation for correct reassembly

Pivot pin that connects the oven door hinge to its mounting bracket. Replace if worn, broken, or missing to restore smooth door operation and alignment.

Mounting screw hardware for ranges and cooktops. Replace missing, stripped, or corroded screws used to secure panels, brackets, or components.

Covers the control panel lamp opening to diffuse light and protect from debris. Replace if broken, cracked, or missing to restore clear indicator visibility.

Small burner not heating? This 6-inch surface element coil plugs into your range burner receptacle to restore heat. Easy DIY plug-in repair.

Support rod that props up the lift-up top on your range. Holds the top panel securely in the raised position for cleaning or servicing. Replace if bent or missing.

Replacement 6-inch burner bowl for electric ranges and cooktops. Houses the burner element. Replace if cracked, chipped, rusted, or discolored beyond cleaning.

If your 8-inch burner won't heat or heats unevenly, this surface coil element is the fix. Direct plug-in replacement takes about 15 minutes to install.

Porcelain drip bowl that sits beneath the 8-inch heating element to catch spills and drips. Replace if cracked, rusted, or discolored for easier cleanup.

Secures wiring harness to prevent rubbing and loose connections. Replace if worn or broken to restore proper wire routing. Confirm fit with your model.

Houses and protects cooktop wiring connections. Replace when the original box is damaged, corroded, or missing fasteners for safe electrical connections.

Thermostat knob assembly for your range. Mounts on the control panel to adjust oven temperature. Replace if cracked, broken, or missing.

Burner won't seat properly or wobbles? This receptacle clip secures the surface element connection for stable, reliable heat. Simple DIY fix.

Burner not heating or terminal block burned? This electric range terminal block kit restores power to surface elements. Easy 10-15 minute DIY repair.