Parts for Ge PGB975SEM4SS: 02 - Control Panel & Cooktop Parts

This right-side end support secures and centers the appliance's rotating assembly so the motor and blower run smoothly. It restores proper alignment and reduces rubbing or wobble that can cause noise or airflow issues. What it does:

• Holds the motor shaft or fan spindle in place to maintain correct rotation alignment
• Keeps the blower/fan wheel properly seated to prevent contact with housing
• Helps reduce vibration and audible noise from a loose or worn support
• Supports reliable airflow by preserving correct component spacing

• One right-side end support

• Disconnect power before starting any repair
• Access may require removing panels or components; keep fasteners organized
• Inspect mating surfaces and brush away debris before installing to ensure a secure fit

This end support is a small mounting bracket that secures the freezer/refrigerator end panel and helps keep the cabinet aligned for smooth door operation and proper seal. It replaces a worn or broken support to restore stability and reduce rattling. What it does:

• Supports and anchors the end panel at the left-front corner of the cabinet
• Maintains correct panel alignment to help doors and seals close properly
• Reduces vibration, shifting, or rattling caused by a damaged or missing support
• Fits into mating slots/tabs on the cabinet frame as the OEM bracket does

• One end support (left-front)

• Basic hand tools required; remove power to appliance before service
• Handle parts carefully to avoid scratching painted surfaces
• Inspect adjacent clips, screws and panels and replace any damaged fasteners

Decorative bezel that fits around the range control area. Replace if cracked, dented, or missing to restore a finished appearance and cover mounting hardware.

Secures components to your appliance chassis for a rattle-free fit. Replace missing, stripped, or corroded screws to keep panels and brackets aligned.

Hex washer head screw for electric ranges. Secures panels, brackets, and internal components. Replace if screw is stripped, missing, or damaged.

If burners won't ignite automatically but light with a match, the spark module likely failed. Accessed from the back of the range, moderate difficulty.

Rubber bumper cushions contact points on range doors and panels. Replace if cracked, missing, or worn to restore quiet operation and protect surfaces.

Replacement oven door hinge for gas and electric ranges. Secures and supports the oven door for smooth opening and closing. Needed when hinge is bent, broken, or door sags. Direct fit replacement part.

Replace worn or damaged stovetop grates with this cast surface burner grate kit. It restores a level, stable cooking surface on your gas range or cooktop so pots and pans sit securely and heat evenly over the burners.

• Supports cookware at the correct height above the burners
• Provides an even, stable surface for moving pots and pans
• Common fix for cracked, warped, or broken grates
• Helps reduce rocking or instability from worn grates

What's included: One surface burner grate kit (cast), as supplied by the manufacturer. Installation notes:

• Allow the cooktop to cool completely before handling grates.
• Lift off old grates; position the new grates so they align properly and sit fully on the cooktop.
• Handle carefully—cast parts can chip or scratch surfaces if dropped.
• Verify each grate sits flat and stable before use.

Replace worn or damaged stovetop grates with this cast surface burner grate kit. It restores a level, stable cooking surface on your gas range or cooktop so pots and pans sit securely and heat evenly over the burners.

• Supports cookware at the correct height above the burners
• Provides an even, stable surface for moving pots and pans
• Common fix for cracked, warped, or broken grates
• Helps reduce rocking or instability from worn grates

What's included: One surface burner grate kit (cast), as supplied by the manufacturer. Installation notes:

• Allow the cooktop to cool completely before handling grates.
• Lift off old grates; position the new grates so they align properly and sit fully on the cooktop.
• Handle carefully—cast parts can chip or scratch surfaces if dropped.
• Verify each grate sits flat and stable before use.

Pin locator for gas ranges. Secures and aligns burner components in proper position. Replace if broken, missing, or worn to restore proper burner assembly.

Cooktop mounting screw secures the cooktop to frame or brackets. Replace if stripped, missing, or rusty to eliminate wobble, rattling, or lifted corners.

Medium burner cap for gas cooktops and ranges. Sits atop the burner head to distribute flame evenly. Replace if cracked, chipped, or worn from use.

Burner cap sits atop the burner base on gas ranges and cooktops. Replace if cracked, chipped, discolored, or missing to restore a clean appearance.

Replacement burner cap for gas cooktops and ranges. Sits atop the burner head to distribute flame evenly. Replace if cracked, chipped, or worn.

Replacement burner cap for 18K high-output burners. Sits atop the burner head to shape and distribute the flame. Replace if cracked, chipped, or worn.

The Top Burner Spark Electrode is an OEM replacement part for GE brand appliances. Compatible with select GE gas ranges, this spark electrode ensures a reliable ignition for your burners. It features a white ceramic base and a metal electrode tip.

Symptoms of a bad igniter:

• Burners not lighting
• Igniter sparking erratically

The causes of a bad part can include physical damage or wear and tear over time.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

Replacement small surface burner for gas ranges and cooktops. Installs on stovetop to provide heat for smaller pots. Replace if damaged, discolored, or missing.

Burner base holds and secures the gas burner assembly on your cooktop. Replace if cracked, warped, or corroded to restore proper burner seating.

Primary gas burner head that directs and distributes flame on your cooktop. Replaces damaged, corroded, or stained burner heads to restore proper function.

Replace your cracked, warped, or missing medium surface burner. Ensures even heat distribution for cooking tasks. Installs on gas range cooktops.

Secures the ignition electrode on gas range burners. Replace if burners won't spark, igniter clicks continuously, or clip is corroded or loose. Confirm fit with your model number.

Mounting screw for range installation and assembly. Replace missing, stripped, or damaged screws to secure panels, brackets, or components properly.

Single fastening screw for range components. Replaces missing, stripped, or damaged screws that secure panels, brackets, and trim pieces in place.

Replacement mounting screw secures panels, brackets, and trim on ranges and cooktops. Install to replace missing, stripped, or rusted fasteners.

Fix a gas burner that won't light or keeps clicking constantly. This spark electrode ignites your burner. Easy 15-minute DIY repair for most ranges.

Burner base mounts beneath the burner cap on gas range cooktops. Replace if cracked, corroded, or damaged to restore proper burner alignment and appearance.

Secures the igniter in its mounting bracket on gas ranges and cooktops. Replace if spring is missing, broken, or worn to restore proper igniter positioning.

Secures the spark igniter to the burner base for reliable ignition. Replace if burner won't light or spark is weak. Verify fit with your model.

Flat cooking surface that fits over range burners for pancakes, eggs, and sandwiches. Replace if cracked, warped, or missing from previous owners.