Parts for Ge CHS985SEL2SS: Control Panel & Cooktop Parts

The Range Top Glass and Front Support Kit is an OEM replacement part for GE electric ranges. As the protective surface above cooktop burners and the frame securing the glass panel, this kit plays an integral role. 

Symptoms of a bad glass top and support include:

• Cracks or chips in the glass cooking surface 
• Looseness, wobbling or movement of the glass panel
• Gaps appearing around the edges of the glass top

Over time, thermal expansion and contraction from cooking temperatures can cause the glass to weaken. Repeated scrubbing or impacts from cookware are also common causes of damage.

This genuine OEM GE part is also compatible with Hotpoint, RCA, and select Kenmore electric ranges.

This indicator sleeve is a small control-knob marker that restores a clear position marker and snug fit on the control shaft for reliable setting selection. It improves dial visibility and stabilizes the knob during use. What it does:

• Covers and centers the control shaft so the knob sits straight and turns smoothly
• Provides a visible pointer for selecting temperature or power settings
• Replaces cracked, worn or missing sleeves that make knob position hard to read
• Helps eliminate wobble or looseness between the knob and control shaft

• One indicator sleeve

• Disconnect power to the appliance before servicing
• Remove the control knob (pull straight off) to access the sleeve
• Press the sleeve onto the shaft by hand until fully seated; no special tools generally required
• If the knob or shaft is damaged, inspect and replace as needed for secure fit

This lower oven warming element heats the oven's warming/holding compartment so food stays warm until serving. Replaces a damaged or non-heating lower element to restore consistent low-temperature operation. What it does:

• Heats the oven's warming/lower compartment for holding cooked food
• Replaces elements that show visible damage, burn-through, or no heat output
• Helps restore even low-temperature performance when the warmer function fails
• Works with the oven's temperature control and safety circuits to provide steady heat

• One lower oven warming element

• Disconnect power at the breaker before beginning any repair
• Wear gloves; element edges and terminals may be sharp
• Verify proper wiring and secure terminal connections during installation

This induction cooktop element replaces a failed high-power burner to restore normal cooking performance on compatible induction ranges. It provides the heating coil assembly required for fast, responsive induction heating. What it does:

• Replaces the induction heating element that generates the magnetic field to heat cookware.
• Restores a burner that no longer heats, heats intermittently, or shows reduced power.
• Helps eliminate error conditions or cooktop lockouts caused by a faulty element.
• Matches the OEM wattage rating for high-output cooking performance.

• Disconnect power at the breaker before servicing; glass cooktops and wiring can be hazardous.
• Handle the glass surface and element assembly carefully to avoid cracks or damage.
• Installation may require removing the cooktop glass and disconnecting wiring—keep fasteners and wiring order noted.

This is a stainless-steel machine screw used to secure components in appliances. Its #8-18 thread and 3/8" length provide a reliable, corrosion-resistant fastening where a short machine screw is required. What it does:

• Fastens panels, brackets, or small assemblies with a #8-18 threaded hole
• Resists rust and corrosion in humid appliance compartments
• Provides a short, secure hold where space is limited
• Compatible with standard #2 Phillips or compatible driver bit for installation

• Power off and unplug the appliance before servicing
• Use the correct driver to avoid stripping the head
• Do not overtighten; stop when snug to avoid thread or component damage
• If replacing multiple fasteners, reuse only the same size and type

The Induction Control and Gasket Kit is an OEM part for GE induction ranges.  

Causes of needing replacement include failure of internal circuitry over extended use, moisture penetration degrading surfaces, or accidental impacts damaging components.

Symptoms requiring attention are:

• Controls and displays unresponsive or faulty
• Temperature calibration malfunctioning
• Induction zones permanently stuck in power modes
• Fault codes indicating electrical or sensor issues

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This induction duct gasket seals the air/heat duct on compatible induction ranges to help maintain proper airflow and reduce heat or steam leakage. It restores the factory seal for safer, more reliable cooktop operation. What it does:

• Seals the duct path beneath the cooktop to help direct hot air and exhaust where intended
• Reduces heat and steam escape that can cause nearby panels to overheat or discolor
• Helps prevent smoke, burning smells, or combustion of debris that may collect in gaps
• Supports proper cooling/venting of internal components for consistent performance

• Disconnect power to the appliance before starting any repair
• Remove cooktop or access panels to reach the duct area
• Clean mating surfaces of old gasket material, grease, and debris before installing the replacement
• Use appropriate hand tools and avoid sharp bending or crushing the gasket during placement

This is a replacement 8-18 x 5/16 machine screw used to secure appliance panels and components. It restores proper fastener fit so parts stay mounted and operate safely. What it does:

• Fastens panels, brackets, and small components where an 8-18 x 5/16 screw is specified
• Prevents loose parts, rattling, and misalignment caused by missing or worn screws
• Provides the correct thread size and length for reliable reattachment
• Works wherever the OEM calls for this specific 8-18 x 5/16 screw

• Turn off and unplug the appliance before starting any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to threads or mounting surfaces
• If replacing multiple fasteners, use matching screws to maintain proper fit and function

The Front Gasket Assembly is an OEM replacement part for GE electric ranges. As the seal between the range body and control panel, the front gasket plays a critical role in containing heat and preventing spills from entering internal components.  

Symptoms of a bad front gasket include:

• Excess heat visible escaping around the control panel 
• Drips or spills entering behind the control panel
• Visible cracks, splits, or openings in the gasket seal

Causes of a bad gasket can be normal wear from repeated cleaning and high-heat cooking. Hard impacts or forced openings may also damage the integrity of the seal over time.

This OEM GE part is also compatible with Hotpoint, RCA, and select Kenmore electric ranges.

The Cooling Fan Sensor is an OEM replacement part for GE ovens and ranges. It is a critical component that monitors and regulates the operation of the cooling fan, ensuring proper ventilation and temperature control within the appliance.

Symptoms of a bad cooling fan sensor:

• Overheating issues, with the oven or range becoming excessively hot
• Failure of the cooling fan to turn on or operate correctly
• Error codes or warning lights related to temperature or ventilation problems
• Potential safety hazards due to inadequate cooling and heat buildup

Causes of a faulty cooling fan sensor can include exposure to high temperatures over time, electrical malfunctions, or physical damage to the sensor or its wiring.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore ovens and ranges.

The Blower Tangential is an OEM component designed specifically for GE ranges. Located near the top of the oven cavity, this tangential blower circulates exhaust air out of the oven and above the cooktop during and after cooking cycles.  

Symptoms of a faulty blower include:

• Excessive heat buildup inside the oven and around the cooktop surfaces
• Steam or smoke failing to properly vent outdoors from the oven  
• Abnormal noises coming from the blower motor

Causes usually involve failures of the electric motor from years of sustained usage. Physical obstructions blocking the fan housing could also lead to issues.

This genuine GE part is compatible with Hotpoint, RCA, and select Kenmore models as well.

A temperature probe that senses oven temperature and sends readings to the control board so the appliance can regulate cooking heat. Replaces a failed or intermittent probe to restore accurate temperature feedback. What it does

• Measures internal oven temperature and provides a signal to the oven control for proper temperature regulation
• Can cause inaccurate baking, uneven cooking, or oven error codes when faulty or open/shorted
• Works as the sensor input used by the control to heat cycles on/off
• Typically mounts inside the oven cavity and connects to the control harness

• One temperature probe (BLE) sensor

• Disconnect power to the appliance before servicing to avoid shock or injury
• Handle the probe and wiring gently; do not kink or sharply bend the sensor lead
• Verify connector alignment and secure fit to the control harness; test continuity per OEM instructions before full reassembly