Parts for Ge JB255RK1SS: Control Panel & Cooktop Parts

A replacement black cooktop glass surface that restores the smooth, easy-to-clean top on select GE electric cooktops. Replaces damaged or worn glass to help maintain a flat, stable surface for burners and cookware. What it does

• Replaces cracked, chipped, deeply scratched or otherwise damaged cooktop glass
• Restores an even, heat-resistant surface for electric burners and cookware
• Helps prevent debris from falling into the cooktop cavity through damaged areas
• Improves cooktop appearance and makes cleaning easier

• One black cooktop glass surface

• Disconnect power to the appliance before beginning any work
• Handle carefully — glass edges can be sharp and the part is fragile; use two people if needed
• Reuse existing trim, brackets or gaskets unless those components are also damaged

Replace a cracked, broken, or loose range valve control knob. This knob installs on the control panel to adjust burner settings. Restores functionality.

Burner won't adjust temperature or stuck on high? This surface burner control switch restores heat control. Quick 10-minute fix with basic tools.

Burner stuck on high or won't heat? This 8-inch infinite switch controls heat output on electric ranges. Simple 20-30 minute DIY replacement.

Indicator light that illuminates when burners or oven are active. Replace if it stays on constantly or fails to light. Verify fit with your model number.

Provides structural support at the end of your range. Replace this support piece if the original is cracked, broken, or missing to restore stability.

Structural support bracket that secures the end of your range. Replaces cracked, broken, or missing end supports to restore stability and proper alignment.

Replacement control bracket for electric and gas ranges. Secures and supports the control panel assembly. Order a new bracket if yours is cracked or broken.

Decorative trim piece surrounding the control panel and knobs on your range. Replace if cracked, discolored, warped, or damaged to restore appearance.

Hex washer head screw for electric ranges. Secures panels, brackets, and internal components. Replace if screw is stripped, missing, or damaged.

This pin locator secures a hinge or shaft pin in place to keep linked appliance components aligned and operating smoothly. It's a small replacement part that restores proper positioning where a locating clip or retainer is used. What it does

• Holds a hinge, shaft, or pivot pin in place to prevent lateral movement
• Restores proper alignment of doors, panels, or linked components
• Helps stop rattling, misalignment, or binding caused by a worn or missing locator
• Works as a direct replacement for the same OEM-labeled locating clip/retainer

• One pin locator

• High-level replacement; basic hand tools usually required
• Disconnect power (and water, if applicable) before servicing appliances with electrical components
• Keep track of small parts and orientation for correct reassembly

Fix F2 error codes, dead oven display, or overheating issues. This oven control board manages temperature and cooking modes. DIY-friendly repair.

Covers the control panel lamp opening to diffuse light and protect from debris. Replace if broken, cracked, or missing to restore clear indicator visibility.

Small burner not heating? This 6-inch surface element coil plugs into your range burner receptacle to restore heat. Easy DIY plug-in repair.

Replacement 6-inch burner bowl for electric ranges and cooktops. Houses the burner element. Replace if cracked, chipped, rusted, or discolored beyond cleaning.

If your 8-inch burner won't heat or heats unevenly, this surface coil element is the fix. Direct plug-in replacement takes about 15 minutes to install.

Porcelain drip bowl that sits beneath the 8-inch heating element to catch spills and drips. Replace if cracked, rusted, or discolored for easier cleanup.

Secures wiring harness to prevent rubbing and loose connections. Replace if worn or broken to restore proper wire routing. Confirm fit with your model.

Package of 12

Panel mounting screw secures trim, bezels, and internal components on ranges and cooktops. Replace when stripped, corroded, or missing to restore fit.

Cooktop box assembly for electric ranges. Houses and supports the cooktop surface. Replace if cracked, damaged, warped, or showing structural wear.

Burner won't seat properly or wobbles? This receptacle clip secures the surface element connection for stable, reliable heat. Simple DIY fix.

Size: 10-32 GXTT FLP.595 S

Burner not heating or terminal block burned? This electric range terminal block kit restores power to surface elements. Easy 10-15 minute DIY repair.