Parts for Ge JM250DF4WW: Control Panel & Cooktop Parts

This is the white front control panel for the console/user-interface area. It restores a clean appearance and a secure mounting surface for the controls so the console fits and feels solid after damage or wear.

• Provides the outer control-console panel that supports/aligns the user interface components
• Protects and positions the keypad/display area for proper fit and feel
• Common replacement reasons: cracked or broken panel, missing/broken tabs, warping, discoloration, or loose/ill-fitting console
• Helps ensure controls sit correctly and are easy to access

• Disconnect power before servicing; be aware the high-voltage capacitor can retain a dangerous charge
• Remove mounting screws/clips and release locking tabs carefully to avoid damage
• Transfer any switches, control board, bracket, or overlay from the original panel as required by your model
• Route wires/ribbons carefully and avoid over-tightening fasteners; test all controls before final reassembly

The Oven Control Board is an OEM part for GE ranges. As the central processor, it controls all cooking operations and digital interface functions.

Causes of needing replacement include moisture exposure deteriorating circuitry over time, power abnormalities damaging sensitive chips, or continuous daily cooking cycles promoting natural wear.

Symptoms requiring attention are:

• Fault codes appearing and knobs/buttons unresponsive
• Inaccurate temperature calibration or modes stuck on/off
• Clean and Convection options permanently disabled
• Bake element or broiler functioning erratically

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This white clock control plate is the front bezel for a range/oven control assembly that restores a clean, readable surface and secures the clock/display area. It replaces a cracked, discolored, or warped front plate to improve appearance and usability. What it does:

• Replaces damaged or faded front bezel for the clock/display area
• Provides a clean, readable surface for time and control labels
• Helps keep underlying clock/control electronics protected from spills and debris
• Restores proper fit and alignment of control buttons and knobs

• One white clock control plate

• Disconnect power to the appliance before starting any repair
• Remove control panel screws and/or retainers to access and replace the plate
• Handle the plate carefully to avoid scratching; align tabs and fasteners before securing

This replacement control knob fits the surface element infinite switch, letting you turn the burner on and choose the heat level. Replace a cracked, stripped, or missing knob to restore smooth, reliable control and a clean, matched finish.

• Attaches to the infinite switch stem to select burner settings from Off to High
• Restores proper feel and engagement when the original knob is worn or broken
• Common symptoms: knob splits, wobbles, falls off, is hard to turn, or won't engage the switch
• Color-matched white to blend with compatible control panels

• Disconnect power to the range/cooktop before servicing
• Pull the old knob straight off the switch stem; avoid prying on the control panel
• Align the new knob with the stem and press firmly until fully seated
• The pointer aligns to Off before restoring power

A light indicator is installed on ranges and wall ovens as a safety feature. The purpose of the light indicator is to tell the user when the appliance is in operation. When the unit is heating up or running, the light indicator will illuminate. A replacement part is necessary if the component is no longer functioning.A visual inspection will determine if the light indicator is working. Turn the oven on, and if the light doesn't glow, it's broken. Replacing the light indicator is a quick and easy process. Unplug the range from its power source before starting. An adjustable wrench or nut driver is required to make the replacement. The light indicator is located inside the cover plate of the appliance.This light indicator is an authentic OEM replacement part. It is sold as an individual unit. It comes sourced directly from the manufacturer. The light indicator is made of durable, high-quality materials. The component is compatible with several models of ranges. It fits into products produced by General Electric, RCA, and Hotpoint.

This part is the lens for a small appliance light on select GE cooking products. It covers and diffuses the lamp, protecting the opening and restoring a clean, finished appearance so status illumination is easy to see.

• Covers and diffuses a panel/indicator light so it's visible without glare
• Helps shield the lamp cavity from grease, moisture, and debris
• Restores proper appearance if the original lens is cracked, missing, or discolored
• Common symptoms: missing or broken lens, cloudy/yellowed lens, exposed indicator lamp

• Disconnect power to the appliance before servicing
• Access the lens from the rear of the panel or mounting area; release retaining tabs or hardware
• Seat the new lens fully and align any tabs before securing
• Restore power and verify the indicator light shines through clearly

This membrane touchpad replaces a worn or unresponsive control keypad so you can operate your appliance's electronic controls reliably. It restores button input and the tactile surface used to select settings. What it does:

• Replaces the front control touchpad used to enter settings and commands
• Restores responsiveness for unregistered or stuck buttons
• Helps resolve issues where button presses don't register or the control feels worn
• Works with the appliance's existing control electronics and mounting

• Disconnect power to the appliance before starting any repairs
• Handle the membrane gently; avoid folding or creasing the flexible circuit
• Re-seat the connector carefully; ensure contacts are clean and aligned
• If the control still behaves oddly after replacement, try a power reset and verify connector seating.

The 6" Surface Burner with Sensor is an OEM part for GE ranges. This part provides precise heating for cooking on your range's stovetop. The integrated sensor helps regulate the burner temperature, ensuring even and consistent cooking results.

Common causes of a bad surface burner include electrical issues, wear and tear over time, or damage from excessive heat or spills.

Symptoms of a bad surface burner with sensor include:

• Burner not heating up
• Inconsistent or uneven heating
• Burner temperature not being properly regulated
• Error codes or malfunction indicators on the range display

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This 8-inch drip bowl sits beneath the surface coil on your range to catch spills and support the element. Replacing a rusted or stained bowl refreshes the cooktop and helps the coil sit level for reliable heating.

• Collects drips and boilovers under the 8-inch surface coil
• Positions and supports the element over the receptacle
• Helps keep the cooktop cleaner and easier to maintain
• Common signs to replace: heavy staining, rust/corrosion, warping, holes, or the element not sitting level

• Disconnect power and allow the cooktop to cool completely
• Lift the coil element slightly, then pull straight out of the receptacle
• Remove the old bowl, align the notch/orientation of the new bowl, and seat it flat
• Reinsert the coil element terminals fully into the receptacle and verify it sits level

Bottom burn box replaces the lower gas burner housing in compatible gas ovens, securing the burner assembly and helping direct heat for steady cooking while protecting internal oven components from flame and debris. What it does

• Houses and positions the lower burner assembly to ensure proper flame direction and ignition.
• Channels heat across the oven floor for more even cooking.
• Shields internal components from direct flame, food spills and debris.
• Common symptoms it can address: burner won't stay lit, irregular or uneven heating, visible corrosion or physical damage to the burner area.

• Always shut off gas supply and electrical power before inspecting or replacing gas-oven components.
• Inspect surrounding gaskets, mounting hardware and the burner assembly; replace any damaged parts.
• Follow OEM service instructions and safety guidelines specific to your oven model.

This is a replacement #8-18 screw, 0.750 inches long with a nickel finish, used to secure panels and components on compatible appliances. It restores proper fastening and helps eliminate loose or rattling parts. What it does:

• Fastens appliance panels, brackets or small components where a #8-18 x 3/4" screw is required
• Replaces missing or damaged screws that cause loose panels, rattles, or misalignment
• Provides a corrosion-resistant nickel finish for longer-lasting attachment
• Matches OEM thread and length for a secure fit

• One (1) screw as shown

• Use the correct screwdriver or bit to avoid stripping the head
• Power off and unplug the appliance before accessing internal panels
• Replace only with the same size and thread to ensure proper fit; do not overtighten