Parts for QAS740RM2SS: Control Panel & Cooktop Parts

This control knob assembly replaces a damaged, loose, or missing range/oven control knob to restore secure grip and reliable selection of heat settings. It provides a simple, direct replacement for the original factory knob. What it does:

• Replaces a cracked, stripped, or missing control knob so settings can be selected and held securely
• Allows smooth rotation and positive detents for accurate temperature or function selection
• Stops slipping or spinning on the control shaft that prevents setting changes
• Helps restore normal operation of the front control interface

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Pull off the old knob straight from the control shaft; inspect the shaft for damage before installing.
• Align the replacement knob with the shaft flat and push firmly until fully seated; do not force or hammer.
• If the knob does not fit or operate smoothly, stop and verify shaft condition.

This metal manifold panel replaces the damaged front control trim on your range, restoring a secure mounting surface for controls and improving the appliance's appearance. It's a direct-fit exterior panel used with the cooktop/range control assembly. What it does:

• Replaces a cracked, dented, or corroded front control/manifold trim panel
• Provides the mounting surface and protection for control valves, switches, and ignitors
• Helps keep spills and debris away from internal control components
• Restores proper alignment and fit of control knobs and trim pieces

• One manifold panel

• Disconnect power (unplug or switch off breaker) and turn off gas supply before starting
• Remove knobs, burner grates, and any trim pieces to access the panel; use appropriate hand tools
• Handle edges carefully — metal panels can be sharp

The Light Lens is an OEM replacement part for GE gas cooktops. It is a small yet important part that covers and protects the indicator light bulb in your cooktop so that the light bulb remains protected from grease, spills, and other potential hazards. 

Symptoms of a faulty light lens include:

• Dim or inadequate lighting in the cooking area
• Difficulty in seeing or monitoring your cooking
• Exposure of the light bulb to grease or spills

A bad light lens can occur due to accidental damage or wear and tear over time. If you notice cracks, discoloration, or any other signs of damage on the lens, it may be time to replace the old or damaged light lens with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This infinite switch controls the heat output of a stove's electric surface element, restoring precise temperature adjustment for cooking. It replaces a worn or failed burner control to regain variable heat settings. What it does:

• Regulates power to an electric cooktop surface element, allowing variable heat levels
• Replaces a faulty control that causes a burner to stay off, stay on, or not change heat settings
• Stops intermittent heating, no-click conditions, or elements that only run at full or low power
• Works with standard knob-style controls

• One infinite switch assembly

• Disconnect power at the breaker before starting any repair to avoid shock
• Remove the knob and console or back panel to access the switch; handle wiring gently
• Match the part number on the switch to your original before installing

This infinite switch is the variable control used to regulate heat on an electric range surface element. It restores adjustable burner heat so you can set and maintain the correct cooking temperature. What it does:

• Controls the power level to a surface heating element, allowing gradual heat adjustments rather than just on/off.
• Can cause symptoms such as a burner that won't heat, heat stuck at one setting, or inability to change element temperature.
• Replaces a failed or intermittently working control that may show no continuity when tested.
• Works with standard knob-operated rangetop elements.

• One infinite switch

• Disconnect power to the appliance at the breaker before starting any repair.
• Replacement typically requires removing the infinite switch from behind the control knob/console—keep track of wiring and clip locations.
• Use a multimeter to confirm the old switch is faulty before replacing.
• If replacing on a glass-ceramic cooktop, follow manufacturer guidance to avoid scratching or damaging the surface.

This oven thermostat senses and cycles the heating element to help maintain the set oven temperature for reliable baking and roasting. It replaces a failed temperature control to restore consistent oven heat. What it does

• Monitors oven temperature and opens/closes the heating circuit to maintain the set temperature
• Can stop the oven from heating or cause inconsistent temperatures when the thermostat fails
• Common symptoms that indicate replacement: oven won't heat, oven overheats, or oven temperature is inconsistent or fluctuates
• Works with the oven's control system to regulate bake/broil cycles

• One oven thermostat

• Disconnect power to the appliance before starting any repair
• Note wire locations or take a photo before disconnecting for correct re-installation
• Handle the temperature-sensing probe and terminal connections gently to avoid damage
• If needed, verify oven temperature with an oven thermometer and follow manufacturer calibration procedures after installation

This is a replacement mounting screw for the refrigerator/freezer thermostat assembly. It secures the thermostat to the cabinet so temperature sensing and control remain stable and reliable. What it does:

• Secures the thermostat housing or bracket to the appliance cabinet
• Keeps the thermostat properly positioned for accurate temperature sensing
• Common fix when a loose, missing, or stripped thermostat fastener causes rattling or poor contact
• Small hardware part used during thermostat replacement or reassembly

• One thermostat mounting screw

• Turn off power to the appliance before starting any repair
• Use appropriate screwdriver and do not overtighten to avoid stripping the housing or threads
• If original hole or threads are damaged, inspect bracket or cabinet and replace as needed

An infinite switch regulates power to a range or cooktop surface element for smooth, variable heat control. Replacing a worn switch restores accurate low-to-high settings and dependable on/off operation for the burner.

• Controls the cycling of power to a surface element based on the knob setting
• Common symptoms of failure: burner won't heat, only heats on high, won't turn off, or temperature can't be adjusted
• Can also cause intermittent heating or an unresponsive/loose-feeling knob if the shaft is damaged

• Disconnect power at the breaker before servicing; high voltage is present
• Access the control area, label/photograph wiring, and transfer leads one at a time to the matching terminals on the new switch
• Mount the switch securely, align the shaft with the knob, and reassemble the panel
• Test the burner through low, medium, and high settings to ensure proper operation

This indicator light is a small panel-mounted lamp that illuminates to show when a heating circuit is active. Replacing a failed indicator restores a clear visual cue so you know when the appliance is operating. What it does

• Lights when the corresponding function or element is energized
• Provides a visual status cue during operation
• Common symptoms: light won't come on, stays on continuously, flickers or is dim, or shows physical damage

• One indicator light assembly

• Disconnect power at the breaker before servicing
• Access the rear of the console/control area; note wire positions and transfer one at a time
• Secure the new light in the panel opening per design (snap-in or nut-mounted)
• Restore power and test operation before reassembly

This pilot indicator light mounts in the control panel and illuminates to show when a surface element or another heating circuit is powered. Replace a burned-out or stuck-on light to restore a clear, reliable power-on warning.

• Lights when the corresponding heating circuit is energized
• Alerts users that heating components are active
• Common symptoms: light does not turn on, stays on constantly, flickers, or is very dim
• Shows physical damage to the lens or terminals when failed

• Disconnect power at the breaker before servicing
• Remove the backguard or control panel cover to access the indicator light from behind
• Note wire positions; move connectors to the new light one at a time and secure the light in the panel
• Restore power and test operation before reassembly

The Range Radiant Element is an OEM replacement part for GE ranges. This 5.5-inch element is situated beneath the glass surface of the electric stovetop. It's designed for tasks that require less surface area but still need quick and even heating, such as simmering sauces or cooking smaller portions of food.

Causes for a malfunctioning Range Radiant Element can include electrical issues like faulty wiring or connections, physical damage from spills or heavy cookware, or wear and tear from regular use.

Symptoms of a bad Range Radiant Element include:

• The element failing to heat up or heating unevenly
• Visible damage such as cracks or burns on the element
• Difficulty in maintaining a consistent temperature

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This seal valve keeps the refrigerator water valve properly sealed to help prevent leaks and water damage. It restores a tight seal where the valve connects to the water line or manifold for reliable dispenser and icemaker operation. What it does:

• Replaces a worn or damaged valve seal to stop water leaks at the water valve connection.
• Helps restore proper water flow control to the dispenser and icemaker when leaks or drips occur.
• Commonly used when you notice water leaking beneath or behind the fridge, puddles under the valve area, or reduced dispenser/ice performance linked to a leak.
• Works as the sealing component between the water valve and its fittings or tubing.

• One seal valve (single replacement seal)

• Disconnect power and shut off the water supply before beginning repairs.
• The valve and fittings are dry, then remove the old seal and install the new seal in the correct orientation.
• Check all tubing and connectors for damage and replace if necessary to ensure a reliable seal.
• After installation, restore water and power, then test the dispenser/icemaker and inspect for leaks.

This replacement backguard restores the finished rear appearance of a freestanding range and helps protect the wall and control area from spills, grease and everyday wear. It provides the proper mounting surface for control components. What it does:

• Covers the rear of the range to hide damage or missing trim and improve appearance
• Protects the wall and control area from splatters, grease and light impact
• Re-establishes the proper mounting and alignment for controls and displays
• Helps stop drafts from behind the range by closing the gap at the back

• Disconnect power to the range before starting any work.
• Some models require removing the cooktop or oven door to access mounting screws; follow your model's service instructions.
• Use basic hand tools; start screws by hand to avoid cross-threading and ensure proper alignment.

This genuine replacement screw secures panels, trim and small components on compatible appliances to restore proper fit and prevent rattling or gaps. Use it when a missing or damaged fastener causes loose or misaligned parts. What it does:

• Fastens panels, bezels, trim pieces and small assemblies to the appliance frame
• Restores secure fit to eliminate rattling, vibration noise or loose trim
• Replaces stripped, rusted or missing screws that prevent proper alignment

• Disconnect power to the appliance before servicing to avoid electrical hazard
• Use the correct screwdriver or driver bit to prevent stripping the head
• Tighten securely but avoid over-torquing; excessive force can strip threads or crack plastics
• Keep removed fasteners organized to ensure correct reassembly

This handle spacer positions the appliance handle at the correct distance from the door or panel for smooth operation. Replacing a worn or missing spacer restores proper standoff, alignment, and feel, and helps prevent rubbing, rattling, or looseness.

• Maintains proper spacing between the handle base and mounting surface
• Helps keep the handle aligned and secure
• Reduces rubbing or contact with the door/panel
• Common fix for a wobbly, misaligned, or scraping handle

• Unplug power and allow hot surfaces to cool before servicing
• Support the door/handle while removing mounting screws to prevent strain
• Note the spacer's position and orientation; reinstall the new spacer in the same location
• Tighten screws snugly; do not overtighten to avoid damage

The Radiant Element Spring is an OEM part for GE electric ranges. This spring supports the radiant element coil and provides the necessary tension to allow the coil to glow red-hot during the cooking process.

Causes of a bad spring can include fatigue from repeated heating and cooling cycles, damage due to impact or mishandling, or corrosion over extended use.

Symptoms of a bad radiant element spring include:

• Radiant element coil sagging or not sitting flush
• Element coil not heating properly or heating unevenly
• Excessive heat and energy use from a misaligned coil
• Element mounting brackets becoming loose over time

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.