Parts for Electrolux EI30SM55JSC: 05 - Control Panel,Door,Miscellaneous Parts

This is a genuine mounting screw used to secure appliance components and panels for a safe, stable fit. It replaces a lost or damaged fastener to restore proper alignment and reduce rattles or loose trim. What it does:

• Secures panels, trim, brackets or small assemblies to the appliance frame
• Prevents vibration-related noise and loose or sagging parts
• Restores proper fit after repair or disassembly
• Useful when the original screw is stripped, missing, or broken

• One mounting screw

• Use the correct screwdriver or bit to avoid stripping the head
• Power off and unplug the appliance before servicing when applicable
• Keep removed hardware organized to ensure correct reassembly
• If threads are damaged, replace with the specified OEM screw only

This end cap finishes and secures the exposed end of a handle, rail, or trim piece on your appliance. It restores a clean look and helps keep the attached component stable during everyday use.

• Covers the open end of a handle/rail and conceals fasteners for a finished appearance
• Helps hold the mating piece in place to reduce looseness, rattling, or wobble
• Replace if the existing cap is cracked, missing, warped, or will not stay attached
• Can help address issues like a loose handle/rail, exposed screws, or sharp/unfinished edges

• Disconnect power to the appliance before servicing; shut off gas/water if applicable
• Note the cap's orientation and any side-specific features before removal
• Release retaining tabs or remove the set screw (as applicable), then align and press/fasten the new cap into place
• Do not overtighten fasteners; verify secure fit and smooth operation after installation

This door latch spring restores the return tension in your microwave's door release mechanism so the latch engages and releases correctly. Replacing a fatigued or broken spring helps ensure safe door operation and reliable interlock switch activation.

• Provides the return force for the latch lever/door release button
• Helps door hooks engage fully and release smoothly
• Supports proper interlock switch actuation so the unit will run only when the door is closed
• Typical failure signs: door won't latch, "open/close door" error, door button sticks, or needing to hold the door shut to start

• Disconnect power. Microwaves can retain dangerous high voltage even when unplugged; discharge the capacitor
• Access the latch assembly behind the control panel; note the spring's orientation and attachment points
• Use needle-nose pliers to install without overstretching; inspect the latch lever and door hooks for wear
• Verify proper door closure and interlock switch operation before reassembly

This replacement end cap finishes and secures the open end of a compatible handle, rail, or trim piece on your appliance. Replacing a cracked or missing cap restores a clean look and helps keep the attached part properly aligned. What it does:

• Covers and protects the exposed end of the mating bar/handle/trim
• Helps keep the connected component seated and prevents shifting
• Replaces broken or missing caps that won't stay attached
• Common signs: loose or wobbly trim/rail, rattling, visible broken tabs, or an uncovered edge

• 1 end cap

• Disconnect power to the appliance before servicing
• Compare the new cap to the original to match orientation
• Transfer and reuse any original screws or clips if your model uses them
• Align tabs and press or slide the cap into place without forcing; verify a secure fit

This replacement frame restores the appliance's outer trim and helps hold the control/door area together for a clean, finished appearance. It's a direct-fit exterior trim piece that replaces damaged or worn frames. What it does:

• Replaces a cracked, chipped, warped or bent trim/frame that affects appearance
• Secures and aligns the surrounding control or door components to reduce gaps and rattles
• Covers internal edges to help keep out dust, moisture and debris
• Restores the original look after impact or wear

• Disconnect power to the appliance before starting any repair
• Remove required trim, screws or clips to access and replace the frame; keep fasteners for reuse unless damaged
• Handle edges carefully—trim pieces can be sharp; use proper hand protection

This replacement hardware mounting fastener secures panels, doors or trim on select Frigidaire appliances to restore stable attachment and reduce vibration. It's a direct-replacement style component used where factory fasteners have worn or been lost. What it does:

• Secures appliance panels, trim pieces, doors or drawers to the cabinet or frame
• Restores proper alignment and reduces rattling or vibration noises
• Prevents loose parts that can catch or rub during operation
• Helps maintain a tight seal and smooth operation of moving components

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Use the correct-size screwdriver or socket; avoid overtightening which can strip threads or damage trim
• Keep removed fasteners and small parts contained to prevent loss during reassembly
• Replace all matching pieces for even fit and alignment

This is a replacement mounting screw used to secure panels, trim, and small components in compatible appliances. Installing the correct screw restores a secure fit and helps stop rattling or loose parts. What it does:

• Secures panels, brackets, trim pieces or small assemblies to the appliance frame
• Prevents parts from shifting, vibrating, or producing rattling noises when in place
• Replaces missing, worn, or stripped fasteners that cause loose doors or misaligned trim
• Works with the original mounting points and thread types used by the manufacturer

• Always disconnect power or unplug the appliance before servicing to avoid electrical hazard.
• Use the correct screwdriver or bit to avoid stripping the head; do not overtighten.
• Keep track of small parts and compare the new screw to the old one before installation.