Parts for Frigidaire FGMV176NTBA: Control Panel,Door Parts

This genuine replacement part is a microwave door assembly. The microwave door assembly consists of the components that make up the microwave door. Over time, a microwave door can become damaged after excessive use. If the door is no longer opening or closing properly or is visibly cracked or damaged, it will need to be replaced. To replace the door assembly, make sure the microwave is unplugged. After it has been powered off, proceed to locate the hinges that attach the door to the frame of the microwave. Once located, find the screws that secure the door to the hinges and begin to unthread the screws. Once removed, lift the door off from its hinges and set it to the sign. Take the new door and line it up with its mounting hinges. Thread the screws to secure the door. Make sure to test the door by opening and closing it, if it opens and closes smoothly then the installation was a success.This OEM part is sourced directly from the manufacturer and is sold individually. It is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand washers.

This genuine replacement part is a microwave door assembly. The microwave door assembly consists of the components that make up the microwave door. Over time, a microwave door can become damaged after excessive use. If the door is no longer opening or closing properly or is visibly cracked or damaged, it will need to be replaced. To replace the door assembly, make sure the microwave is unplugged. After it has been powered off, proceed to locate the hinges that attach the door to the frame of the microwave. Once located, find the screws that secure the door to the hinges and begin to unthread the screws. Once removed, lift the door off from its hinges and set it to the sign. Take the new door and line it up with its mounting hinges. Thread the screws to secure the door. Make sure to test the door by opening and closing it, if it opens and closes smoothly then the installation was a success.This OEM part is sourced directly from the manufacturer and is sold individually. It is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand washers.

This Frame is an OEM part for Frigidaire microwaves. Designed to provide structural integrity and aesthetic appeal, this frame is a crucial component for the proper alignment and protection of the microwave's door and interface. 

The degradation of a microwave frame can occur due to physical impacts, frequent usage, material fatigue, or environmental factors. A compromised frame can affect the door alignment, sealing, and overall look of the microwave.

Symptoms of a bad frame include:

• Difficulty in opening or closing the microwave door.
• A visible gap or misalignment of the door.
• Cracks or breakages on the frame itself.
• Unusual noises when the door is in operation.
• The door not sealing properly, leading to heat loss or inefficient cooking.

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
 

The Door Latch is an OEM part for Frigidaire microwaves. It is a component that secures the microwave door closed during cooking functions and prevents it from accidentally opening. The latch is designed with a sturdy spring-loaded mechanism to provide a secure seal around the door opening.

Causes of a bad latch can include wear and tear over time, damage from repeated use, or failure of the latch spring or locking mechanism.

Symptoms of a bad microwave door latch include:

• The door not closing or latching securely
• Difficulty or inability to lock the door closed
• The door popping or swinging open during a cooking cycle
• Reduced power or inability to operate cooking functions

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This coiled tension spring restores proper tension and movement for the appliance component it supports, helping doors, lids or moving mechanisms operate smoothly and reliably after the original spring wears or breaks. What it does:

• Provides restoring tension to return and hold moving parts (doors, lids, levers) in their correct position.
• Replaces worn or broken springs that can cause sagging, failure to stay closed, or loose/rattling motion.
• Reduces squeaks or abnormal noise caused by a compromised spring.
• Restores predictable, even movement when installed in the original mounting orientation.

• Always disconnect power (and water/gas if applicable) before starting any repair.
• Use appropriate tools and wear eye protection; springs can store tension and may release suddenly.
• Note the spring's orientation and attachment points before removal so the replacement installs the same way.

This replacement outer refrigerator door handle restores a secure grip and smooth opening for affected doors. It replaces a cracked, loose or broken handle so you can open the fridge safely and confidently. What it does:

• Provides a sturdy grip point for opening the refrigerator door
• Replaces cracked, broken or worn handles that won't secure to the door
• Stops the handle from wobbling or pulling away from the door surface
• Helps restore normal door operation and reduce accidental slippage

• One outer refrigerator door handle

• Unplug the appliance or shut off power to the unit before starting work
• Support the door while removing and installing the handle to avoid damage or tipping
• Installation typically requires common hand tools; follow OEM instructions for fastener locations
• Replace with manufacturer-specified fasteners

This replacement door handle restores a solid grip and smooth opening for a refrigerator door. It replaces a cracked, broken, or loose handle so you can open the door confidently and protect the door edge from further damage. What it does:

• Provides a secure grip to open and close the refrigerator door
• Replaces handles that are cracked, split, loose, or missing
• Helps protect the door surface and finish from wear at the pull point
• Matches the original mounting points for a direct swap on compatible units

• High-level, user-installable: remove the old handle hardware, align the new handle, and fasten with the original screws or hardware
• Use the correct screws and torque to avoid stripping or cracking the handle
• Always unplug or power off the appliance or follow manufacturer safety instructions if required for your model