Parts for Ikea 50469293: Control Panel,Door Parts

This electronic control assembly manages oven functions, timing and user interface so your range responds correctly to temperature and timer settings. Replaces a failed or unresponsive control to restore normal oven operation. What it does:

• Houses the oven's main control electronics and clock/timer functions
• Processes user inputs from the touchpad/controls and runs selected bake/broil cycles
• Enables temperature control and cycle timing for consistent cooking
• Commonly used when the oven won't heat, display is blank or erratic, or controls don't respond

• Disconnect power at the breaker before accessing or replacing the control
• Handle the control and display gently to avoid damage to the glass/display and ribbon connectors
• Keep mounting hardware and connectors oriented for correct reassembly; verify all wire connections are secure

This electronic control board replaces the refrigerator's main circuit board to restore control of functions and display operation. It manages timed cycles and user inputs so the appliance responds correctly to settings. What it does

• Receives signals from the user interface and sends commands to components.
• Controls defrost and cooling cycles; failures can cause display errors or unresponsive controls.
• Common symptoms: unlit or flashing display, buttons that don't work, erratic cooling or defrost behavior.
• Replacing the board often resolves control-related faults when wiring and sensors are otherwise good.

• One electronic control board.

• Always disconnect power before servicing to avoid shock or shorting the board.
• Handle the board by edges and avoid static discharge; ground yourself or use an ESD strap.
• Verify connectors and wiring harness seating before and after installation; do not force connectors.
• If problems persist after replacement, check related sensors, harnesses, and fuses — the board only controls signals it receives.

A complete door assembly that replaces a damaged, dented, or non-sealing appliance door to restore proper closure and appearance. Fits the original mounting points for straightforward swap-out. What it does:

• Replaces a cracked, dented, or bent door so the appliance seals and functions correctly
• Restores the exterior appearance and protects internal components from damage
• Helps prevent temperature loss or improper cooking/cooling caused by a damaged door
• Eliminates rattling or binding caused by warped or broken door structure

• Disconnect power and follow all safety steps in your owner's manual before starting
• Door assemblies are heavy or awkward—use two people to avoid injury or product damage
• Retain and reuse any original screws or brackets unless replacement hardware is provided
• Refer to the OEM service instructions for hinge alignment and final adjustment

This control panel is the exterior console overlay that covers and protects the appliance's control area while providing the user interface for cycle selection and settings. It restores the appearance and tactile surface of the console. What it does

• Covers and protects the control buttons, touchpads, or display from dirt and damage
• Provides the visible surface for user controls and labels
• Helps prevent moisture and debris from reaching internal control components
• Commonly replaced when the panel is cracked, scratched, delaminated, or buttons/labels are worn

• Disconnect power to the appliance before beginning any work.
• Use proper tools to remove screws, trim, or clips; avoid prying on fragile plastic.
• Handle the panel carefully to prevent scratching; align clips and tabs during reinstallation.
• If the panel attaches to electronic components, avoid touching circuit boards and reconnect any cables securely.

The Door Latch is an OEM part for Frigidaire microwaves. It is a component that secures the microwave door closed during cooking functions and prevents it from accidentally opening. The latch is designed with a sturdy spring-loaded mechanism to provide a secure seal around the door opening.

Causes of a bad latch can include wear and tear over time, damage from repeated use, or failure of the latch spring or locking mechanism.

Symptoms of a bad microwave door latch include:

• The door not closing or latching securely
• Difficulty or inability to lock the door closed
• The door popping or swinging open during a cooking cycle
• Reduced power or inability to operate cooking functions

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This coiled tension spring restores proper tension and movement for the appliance component it supports, helping doors, lids or moving mechanisms operate smoothly and reliably after the original spring wears or breaks. What it does:

• Provides restoring tension to return and hold moving parts (doors, lids, levers) in their correct position.
• Replaces worn or broken springs that can cause sagging, failure to stay closed, or loose/rattling motion.
• Reduces squeaks or abnormal noise caused by a compromised spring.
• Restores predictable, even movement when installed in the original mounting orientation.

• Always disconnect power (and water/gas if applicable) before starting any repair.
• Use appropriate tools and wear eye protection; springs can store tension and may release suddenly.
• Note the spring's orientation and attachment points before removal so the replacement installs the same way.

This holder is a small mounting clip used to secure components inside the appliance, helping keep internal parts stable and reducing noise from loose fittings. It's a straightforward replacement when the original clip is broken or missing. What it does:

• Secures panels, trim, or small assemblies to prevent shifting or rattling
• Restores proper alignment of the component it supports
• Commonly replaced when cracked, deformed, or lost during service
• Helps reduce vibration-related noise from loose parts

• One holder as pictured

• Turn off power to the appliance before servicing to avoid shock or injury
• Remove surrounding trim or panels as needed to access the mounting location
• Confirm orientation and engagement before snapping into place; do not force if misaligned