Parts for Kitchenaid KEWS145SPA04: 01 - Control Panel & Drawer Parts

Replacement rack for warming drawer. Installs inside drawer cavity to hold dishes and pans. Order if original rack is bent, warped, or missing.

Replace the control panel on your warming drawer. This exterior panel houses the control interface and needs replacement when cracked, scratched, or damaged.

This oven door gasket creates a tight seal between the oven door and cavity to help retain heat for even cooking and improved energy efficiency. Designed to replace a worn or damaged gasket and restore proper door closure. What it does:

• Seals the oven door to minimize heat loss and help maintain set temperatures
• Helps prevent cooking inconsistencies, long cook times, and burnt door edges caused by leaks
• Reduces heat transfer to surrounding cabinetry and floor surfaces
• Restores a snug door closure and reduces energy waste

• One oven door gasket

• Only install when the oven is cool and power (or gas) is disconnected for safety
• Remove the old gasket by pulling from the channel; press the new gasket into the channel evenly around the door
• Ensure the gasket's sealing lip faces the oven cavity so it seats properly when the door closes
• If the door is heavy or awkward to handle, get help to avoid injury or damage

This warming drawer insert restores the removable drawer that keeps cooked food warm until serving. It replaces the drawer component for select built-in warming drawers to return proper fit and function. What it does:

• Provides the removable inner drawer used to hold and retrieve warmed dishes
• Re-establishes correct drawer fit and sliding function in the warming drawer cavity
• Helps maintain heated food placement while the drawer is closed
• Addresses symptoms like a missing, damaged, or ill-fitting drawer insert

• One warming drawer insert

• Turn off power to the appliance before servicing and allow surfaces to cool
• Remove existing drawer per manufacturer instructions before installing the replacement
• Align drawer slides and guide rails, then slide fully into place to confirm proper fit

This ground screw secures the appliance's grounding wire or strap to the chassis or terminal area, creating a reliable bonding point. Replace a missing or damaged screw to restore a proper ground connection during installation or service.

• Provides the designated bonding point for the grounding wire/strap
• Fastens to the frame or terminal area using 8-32 machine threads
• Helps maintain a consistent ground path for safe operation
• Typical reasons to replace: stripped head/threads, corrosion, or a missing screw

• Disconnect power at the breaker or unplug the appliance before servicing
• Route the ground wire/strap to the specified grounding location
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Ensure the ground connection is secure and complies with local electrical codes before restoring power

This nameplate displays your dishwasher's model information and operating instructions for easy reference. It adheres to the appliance's exterior and provides important safety and usage details. Replace this nameplate if it becomes illegible, peels off, or gets damaged during cleaning.

Replaces a cracked, broken, or missing control knob on your warming drawer's control panel. Restores reliable setting selection and complete appearance.

Warming drawer indicator light bulb illuminates control panel to show unit is operating. Replace when light fails or flickers. Verify fit with model number.

This replacement screw secures appliance panels and components so they stay tight and aligned during use. Replacing a missing or damaged screw restores a solid fit and helps eliminate rattles, loose trim, or shifting parts.

• Fastens brackets, panels, trim, or components to the appliance chassis
• Helps correct loose or missing hardware after vibration or service
• Replaces stripped, rusted, or broken screws
• Can reduce rattling noises or misaligned parts caused by missing fasteners

• Disconnect power; for gas appliances, also shut off the gas supply
• Support the part being fastened; start threads by hand to avoid cross-threading
• Use the correct driver size; tighten snugly without overtightening
• Replace hardware with the exact part number to ensure proper fit

This washer installs on your grill or warming drawer to secure components and ensure proper spacing. Replace if cracked, worn, or missing.

Replacement mounting clip for warming drawer installation. Secures drawer components in place. Order a new clip if original is broken, missing, or damaged.