Parts for Kitchenaid KOWT100EBS00: Control Panel And Drawer Parts

The Nameplate is an OEM part for Whirlpool appliances. It serves as an identification label, typically displaying the brand name and model number, providing a clean and professional appearance for the appliance.

You should replace this nameplate if it becomes damaged or worn out. Common causes of a bad nameplate include wear and tear from regular cleaning, exposure to moisture or heat that can cause peeling or fading, and accidental impact that can lead to cracks or detachment.

Symptoms of a bad nameplate include:

• Fading or illegible text
• Peeling or detaching from the appliance surface
• Visible cracks or damage
• The nameplatae being completely missing

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This control knob replaces a cracked or missing knob on your appliance's control panel. It restores positive engagement with the underlying control so you can select settings reliably and keep the front of the unit looking complete.

• Attaches to a keyed or D-flat shaft to operate the switch, valve, or timer underneath
• Allows you to choose cycles, temperatures, or burner levels as designed
• Common symptoms: knob cracked, stripped, loose/spins without engaging, falls off, or missing pointer
• Helps restore normal operation and a finished, uniform appearance

• Disconnect power; for gas appliances, also shut off the gas supply
• Pull the old knob straight off the shaft—do not pry against the bezel or panel
• Align the new knob's opening with the shaft and press firmly until fully seated
• Test the control to confirm proper engagement and function

This rail pan is a replacement drip tray that captures and directs water away from internal components, helping prevent leaks and water damage. It's a direct-fit replacement when the original pan is cracked, warped, or missing. What it does:

• Collects and channels condensation or leak water to the appliance drain area
• Protects internal electronics and cabinet base from moisture
• Restores proper water routing to stop pooling under the unit
• Helps maintain reliable operation by replacing damaged or deformed pans

• Disconnect power and water before accessing the part
• Remove surrounding panels or components only as needed to access the pan; keep hardware organized
• Inspect adjoining seals and mounting clips; replace if damaged to ensure a secure, leak-free fit
• Handle gently to avoid bending the pan; test for proper routing and no leaks after reassembly

This genuine replacement screw restores secure mounting of panels and components on Whirlpool appliances, helping stop loose or rattling parts and maintain proper fit. Small but essential fastener for routine repairs. What it does:

• Secures panels, trim, brackets or small components to appliance frames
• Replaces missing, damaged, or stripped screws that cause loose or misaligned parts
• Helps stop vibration noise and restore proper panel alignment
• Provides the correct thread and length for the original mounting location

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or part damage
• Turn off and unplug the appliance before accessing internal components
• Keep removed fasteners organized so you return them to the original locations

This spacer is a small mounting component that helps keep internal appliance parts correctly positioned for reliable, quiet operation. Use it to restore proper spacing and reduce rubbing or vibration between parts. What it does:

• Provides correct spacing between components to maintain alignment and prevent contact
• Helps reduce noise and vibration caused by misaligned parts
• Supports stable assembly of panels, brackets, or housings where used
• Commonly replaced when worn, cracked, or missing

• Disconnect power (and water, if applicable) before beginning any repair
• Installation typically requires removing an access panel and replacing the old spacer with the new one
• Use basic hand tools; avoid forcing parts into position to prevent damage

This factory fastener secures appliance components so panels, brackets, and handles stay tight and aligned. Replace a missing or stripped screw to stop rattles and keep assemblies firmly in place.

• Fastens appliance parts such as panels, brackets, trim, or hardware
• Replaces a missing, loose, or stripped fastener
• Helps eliminate vibration noise and wobbly components
• Restores proper alignment and secure mounting

• Disconnect power; for water- or gas-connected appliances, shut off supply lines before service
• Match length/thread to the original location; start threads by hand to avoid cross-threading
• Use the correct driver bit to prevent stripping the head
• Tighten snugly; do not overtighten into plastic or thin sheet metal