Parts for Frigidaire FDB939GFT2: 02 - Control Panel Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Almond control panel touch pad for your dishwasher. Replaces cracked, discolored, or worn panels. Installs on the front door to restore appearance.

Fix a dishwasher that won't start, stops mid-cycle, or shows error codes with this control board. Moderately complex repair requiring basic tools.

Replace your dishwasher's vent door liner O-ring seal to prevent leaks and maintain proper drying. Check your model number for exact compatibility.

The dishwasher air vent actuator controls the opening and closing of the drying vent during wash cycles. Positioned near the door assembly, replace it when dishes remain wet after cycles or you notice steam escaping during operation.

Vapor chamber duct for dishwashers. Installs in the drying system to channel steam and moisture. Replace if cracked, broken, or missing for proper venting.

Almond nameplate assembly for dishwasher control panel. Replace worn, faded, cracked, or missing nameplates to restore the clean appearance of your unit.

6 - 10 x 3/8, pan plask, switch

Phillips head mounting screw for dishwashers and ranges. Secures internal components and panels. Replace if stripped, rusted, or missing during repairs.

This replacement mounting screw secures panels and components in compatible Frigidaire appliances, helping restore stable assembly and safe operation. It's a direct-fit fastener used where the original screw has been lost or damaged. What it does

• Fastens appliance panels, brackets, and small parts to restore secure assembly
• Replaces stripped, rusted, or missing screws that can cause rattling or loose components
• Matches the OEM fit for reliable retention and alignment during normal use

• Use the correct size driver to avoid stripping the head; tighten until snug but do not overtighten
• Disconnect power or follow appliance-specific safety procedures if working near electrical components
• Inspect surrounding hardware and replace as needed

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Almond nameplate assembly for dishwasher control panel. Replace worn, faded, cracked, or missing nameplates to restore the clean appearance of your unit.

This replacement mounting screw secures panels and components in compatible Frigidaire appliances, helping restore stable assembly and safe operation. It's a direct-fit fastener used where the original screw has been lost or damaged. What it does

• Fastens appliance panels, brackets, and small parts to restore secure assembly
• Replaces stripped, rusted, or missing screws that can cause rattling or loose components
• Matches the OEM fit for reliable retention and alignment during normal use

• Use the correct size driver to avoid stripping the head; tighten until snug but do not overtighten
• Disconnect power or follow appliance-specific safety procedures if working near electrical components
• Inspect surrounding hardware and replace as needed

Phillips head mounting screw for dishwashers and ranges. Secures internal components and panels. Replace if stripped, rusted, or missing during repairs.

6 - 10 x 3/8, pan plask, switch

No.10 - 16 x 3/8

Secure hose clamp for dishwashers and washers. Replace if worn, loose, or leaking. Verify fit with your model number before ordering.

Red

Replacement mounting screw for dishwasher panels and internal components. Needed when original screws are stripped, missing, or corroded during repairs.

Replacement mounting screws that secure your cooktop to the countertop or cabinet. Essential when original screws are stripped, missing, or damaged during installation or service.

Replaces missing, torn, or saturated sound-dampening insulation blanket for dishwashers. Wraps around tub to reduce noise and protect cabinetry.

Replaces missing, torn, or saturated sound-dampening insulation blanket for dishwashers. Wraps around tub to reduce noise and protect cabinetry.

This side mounting bracket kit includes the hardware needed to secure a dishwasher to the adjacent cabinetry from the sides rather than from the countertop. It is commonly used in kitchens with granite, stone, or other countertops where top-mounting screws cannot be used. Replace this kit if the original brackets are bent, broken, or missing, causing the dishwasher to shift or slide during operation.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.