Parts for Frigidaire FEC36C4ASD: 03 - Control Panel Parts

The Control Knob is an OEM replacement part for Frigidaire ranges and cooktops. It measures about 2-1/2 inches in diameter. It allows users to control the heat settings for burners or the oven, ensuring precise temperature adjustments during cooking. The knob is designed to fit securely onto the control shaft, providing a user-friendly interface for operating the appliance.

Over time, control knobs can wear out or become damaged due to repeated use, accidental impacts, or exposure to high temperatures. A broken or malfunctioning knob can make it difficult to adjust or control the appliance effectively.

Symptoms of a bad control knob include:

• Difficulty turning the knob or it spinning freely without engaging
• Cracks, breaks, or visible damage to the knob
• The appliance not responding to adjustments made with the knob
• The knob not staying securely attached to the control shaft

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This electrical microswitch opens or closes a circuit when its actuator is engaged, allowing the control to sense position or enable a function. Replacing a worn switch restores reliable signaling and prevents intermittent faults in select ranges and wall ovens. What it does

• Changes state (open/closed) when actuated to complete or break a circuit
• Sends feedback to the control or enables power to a related component
• Helps ensure operations start/stop only when the mechanism is in the correct position
• Failure signs can include intermittent operation, cycles that won't start or finish, or related error codes/alarms

• 1 switch

• Disconnect power at the breaker before servicing
• Note/photograph wire positions and transfer one at a time to the new switch
• Match actuator orientation to the original and secure the switch firmly
• Verify function with a multimeter (continuity changes when actuated) before reassembly and testing

The Range Switch is an OEM part for Frigidaire ranges. This switch controls the power supply to the range elements, allowing you to adjust the heat levels for cooking.

Causes of a bad Range Switch can include wear and tear from regular use, electrical issues such as short circuits or faulty wiring, or damage due to spills or overheating. These issues can result in the switch failing to regulate the power to the elements properly.

Symptoms of a bad Range Switch include:

• Inability to adjust the heat level
• The element not turning on or off
• Intermittent or inconsistent heating
• A burnt smell or visible damage on the switch

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This switch bushing fits the control shaft to stabilize and guide rotary switches, helping restore proper knob alignment and smooth operation. It prevents wobble and uneven contact that can cause intermittent control behavior. What it does:

• Centers and supports the control shaft to keep the switch and knob aligned
• Reduces wobble and lateral play that can make knobs feel loose or inconsistent
• Helps maintain reliable electrical contact by keeping the switch properly seated
• Commonly replaced when knobs are loose, the switch wobbles, or control engagement is uneven

• One switch bushing

• Disconnect power to the appliance before starting any repair
• Requires removing the control panel or knob to access the switch shaft; small hand tools typically needed
• Inspect the switch and knob for wear while replacing the bushing; replace worn components as needed

Specs: 10-32 X 0.375

Replacement machine screw used to secure appliance panels and internal components, restoring a stable fit and reducing rattling. Matches a 10-32 thread with a 17/32-inch length for original fastener locations. What it does:

• Fastens panels, trim pieces, and internal brackets; a missing or damaged screw can cause loose panels or rattling noises.
• Secures knobs, control housings and small assemblies to prevent wobble or misalignment.
• Restores proper fit for components so doors and access panels sit evenly and function reliably.

• Disconnect power (unplug or shut off circuit) before accessing components.
• Use the correct driver and tighten by hand; avoid overtightening to prevent stripped threads or cracked plastic.
• Keep any original washers or clips and reinstall them with the screw.