Parts for Frigidaire FFEC3005UBA: Control Panel Parts

This plate is a flat mounting plate used to secure internal components and assemblies on compatible Frigidaire appliances. It provides a stable attachment point to keep parts aligned and reduce vibration for reliable operation. What it does:

• Serves as a mounting/support plate that fastens appliance components in place
• Helps keep moving parts aligned to prevent rattling or misalignment
• Restores secure attachment when a worn or damaged plate causes loose panels or parts
• Commonly used where a flat bracket or support is required inside the appliance

• Disconnect power (unplug appliance or shut off circuit breaker) before starting any repair
• Remove surrounding panels as needed to access the mounting location; keep hardware for reuse unless damaged
• Reuse original screws if in good condition; replace stripped or damaged fasteners

This replacement cover is a molded housing piece that protects internal components and restores the appliance's finished appearance. It keeps wiring and mechanisms shielded from dirt and accidental contact for safer, cleaner operation. What it does

• Covers and protects internal components from dust, debris, and casual contact
• Restores damaged or missing exterior trim for a finished look
• Helps maintain proper airflow or clearance around components when undamaged
• Commonly replaced when cracked, broken, or warped

• One replacement cover as shown

• Disconnect power before servicing to avoid shock or injury
• Remove any retaining screws or clips and note their orientation for reassembly
• Handle gently to avoid cracking plastic; align tabs before fastening
• Replace missing or damaged fasteners with OEM-equivalent parts

This replacement control knob lets you turn the range's control shaft to set burner or oven temperature. Swapping a cracked or loose knob restores a secure grip and accurate, easy selection of settings.

• Attaches to the control stem to adjust heat levels or oven temperature
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps when the knob falls off or spins without engaging the control
• Restores proper feel and alignment of settings on the control panel

• Ensure the appliance is off and cool before servicing
• Pull the old knob straight off the stem; do not twist or pry with tools
• Align the new knob with the stem orientation and press firmly until fully seated
• If the knob won't seat, inspect the control stem for wear or damage before forcing

This electrical microswitch opens or closes a circuit when its actuator is engaged, allowing the control to sense position or enable a function. Replacing a worn switch restores reliable signaling and prevents intermittent faults in select ranges and wall ovens. What it does

• Changes state (open/closed) when actuated to complete or break a circuit
• Sends feedback to the control or enables power to a related component
• Helps ensure operations start/stop only when the mechanism is in the correct position
• Failure signs can include intermittent operation, cycles that won't start or finish, or related error codes/alarms

• 1 switch

• Disconnect power at the breaker before servicing
• Note/photograph wire positions and transfer one at a time to the new switch
• Match actuator orientation to the original and secure the switch firmly
• Verify function with a multimeter (continuity changes when actuated) before reassembly and testing

The Range Switch is an OEM part for Frigidaire ranges. This switch controls the power supply to the range elements, allowing you to adjust the heat levels for cooking.

Causes of a bad Range Switch can include wear and tear from regular use, electrical issues such as short circuits or faulty wiring, or damage due to spills or overheating. These issues can result in the switch failing to regulate the power to the elements properly.

Symptoms of a bad Range Switch include:

• Inability to adjust the heat level
• The element not turning on or off
• Intermittent or inconsistent heating
• A burnt smell or visible damage on the switch

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This switch bushing fits the control shaft to stabilize and guide rotary switches, helping restore proper knob alignment and smooth operation. It prevents wobble and uneven contact that can cause intermittent control behavior. What it does:

• Centers and supports the control shaft to keep the switch and knob aligned
• Reduces wobble and lateral play that can make knobs feel loose or inconsistent
• Helps maintain reliable electrical contact by keeping the switch properly seated
• Commonly replaced when knobs are loose, the switch wobbles, or control engagement is uneven

• One switch bushing

• Disconnect power to the appliance before starting any repair
• Requires removing the control panel or knob to access the switch shaft; small hand tools typically needed
• Inspect the switch and knob for wear while replacing the bushing; replace worn components as needed