Parts for Frigidaire GLD2250RDC2: 03 - Control Panel Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Replace your dishwasher's cover if it's cracked, broken, or missing. This protective cover installs to conceal and protect internal components.

Includes actuator

Includes actuator

Replacement vent adapter for your dishwasher. Connects ventilation components to ensure proper airflow. Order a new adapter if yours is cracked or damaged.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Mounting screw for dishwasher assembly. Secures internal components and panels. Replace if missing, stripped, or corroded during maintenance or repair.

Mounting screw for dishwasher assembly. Secures internal components and panels. Replace if missing, stripped, or corroded during maintenance or repair.

6 - 10 x 3/8, pan plask, switch

6 - 10 x 3/8, pan plask, switch

Replacement mounting screw for dishwasher panels and components. Secures loose panels, brackets, and trim. Needed when original fasteners are missing, stripped, or worn.

Replacement mounting screw for dishwasher panels and components. Secures loose panels, brackets, and trim. Needed when original fasteners are missing, stripped, or worn.

This is a rubber or foam gasket that seals around the electronic control board cover on the dishwasher door. It prevents moisture, steam, and detergent residue from reaching the control board electronics during wash cycles. Replace this gasket if you notice water damage to the control board, intermittent electronic failures, or if the gasket appears cracked, flattened, or missing.

This is a rubber or foam gasket that seals around the electronic control board cover on the dishwasher door. It prevents moisture, steam, and detergent residue from reaching the control board electronics during wash cycles. Replace this gasket if you notice water damage to the control board, intermittent electronic failures, or if the gasket appears cracked, flattened, or missing.

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

This side mounting bracket kit includes the hardware needed to secure a dishwasher to the adjacent cabinetry from the sides rather than from the countertop. It is commonly used in kitchens with granite, stone, or other countertops where top-mounting screws cannot be used. Replace this kit if the original brackets are bent, broken, or missing, causing the dishwasher to shift or slide during operation.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.