Parts for Ge JS750EF4ES: Control Panel Parts

If your range display is blank, shows error codes, or won't maintain temperature, the control board is likely failed. DIY repair in 30 minutes.

Control panel faceplate graphics overlay for electric ranges. Adhesive overlay replaces worn, faded, or damaged graphics on the touchpad area.

Fix a burner stuck on high, won't heat, or indicator light stays on. This infinite control switch regulates surface burner temperature. 20-minute repair.

Burner stuck on high or won't adjust temperature? This range infinite switch controls surface element heat levels. Common DIY fix for uneven heating.

Seals your electric range faceplate to prevent moisture, dust, and debris from entering. Replace when worn or damaged to restore a snug fit. Confirm fit.

Range burner won't shut off or heat properly? The infinite switch controls burner temperature. DIY-friendly repair takes about 15-20 minutes.

Seals the console to keep moisture, grease, and debris from reaching electronics. Replace if crushed, torn, or allowing contaminants in. Confirm fit.

Replace your cracked or faded control panel insert to restore your range's appearance and protect controls. Trim piece allows panel lighting through. Verify fit with your model number before ordering.

Secures the small clear lens in your range's control panel opening. Replace if cracked, broken, or missing to restore a snug fit and proper appearance.

Replace a cracked, stripped, or missing control knob on your electric range. This knob assembly fits the control shaft to restore smooth temperature settings.

Indicator light for range control panels. Illuminates to show when burners or functions are active. Replace when dim, flickering, or burned out. Verify fit with your model number.

Secures the clear lens on your range's control panel. Replace if cracked, broken, or missing to keep the lens properly seated and prevent shifting or rattling.

This wire harness connects the infinite burner control to the cooktop's wiring, restoring proper electrical routing for surface element regulation. It replaces a damaged or worn harness to help re-establish safe, reliable burner control. What it does:

• Provides the correct wiring connection between the infinite switch and cooktop terminals.
• Restores electrical continuity when a frayed, burned, or disconnected harness prevents burner operation.
• Helps eliminate intermittent or no-heat symptoms caused by broken wires or loose terminals.
• Maintains OEM routing and connector fit for consistent control response.

• One wire harness for infinite control (exact OEM configuration)

• Disconnect all power to the range at the breaker before starting work.
• Handle connectors gently; use proper tools to release terminals without bending.
• Verify proper connector seating and secure routing away from heat sources before restoring power.
• If terminals or the infinite switch show damage, replace the affected components as recommended.

This wire harness connects the infinite control switch to the cooktop wiring, restoring proper electrical connection so the surface burner control responds correctly. Designed to replace damaged, burned, or frayed switch wiring. What it does:

• Carries power and control signals between the infinite (surface burner) control switch and the cooktop wiring.
• Helps stop intermittent burner operation, loss of heat control, or no power to a burner when the harness is damaged.
• Replaces melted, cracked, or corroded wires and connectors that cause arcing or unreliable switch function.
• Matches OEM connector types and routing so the switch operates as intended.

• Disconnect power to the appliance before inspecting or replacing the harness to avoid shock or injury.
• Route and secure wiring away from hot surfaces and moving parts; avoid pinching or sharp bends.

Replacement mounting screw for appliances. Secures components and reduces vibration. Needed when original screws are missing, stripped, or damaged.

Mounting screw secures panels, trim, and internal components in ranges and ovens. Replace if missing, stripped, or damaged to restore proper fit.

Replacement mounting screw for securing panels, trim, and internal brackets. Needed when original fasteners are missing, stripped, or damaged.

Black hex washer screw for securing range components like door trim, control panels, and internal brackets. Replace missing or stripped screws during repairs.

Range burner clip secures burner components in place. Replace if bent, broken, or burners wobble. Verify fit with your model number before ordering.