Parts for Kenmore 587.15259400 (58715259400, 587 15259400): Control Panel Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Replacement touch pad panel for your dishwasher's control interface. Installs on the front console. Needed when buttons are cracked, worn, or unresponsive.

Dishwasher won't start or displays flashing lights? The control board manages cycles, detergent dispenser, and water release. DIY repair in 10 minutes.

This is the user control and display board located on the front panel of the dishwasher. It contains the buttons, display, and interface circuitry that allow you to select wash cycles, options, and monitor cycle status. Replace this board if the display is blank or flickering, buttons are unresponsive, or the dishwasher does not respond to cycle selections.

Includes actuator

Includes actuator

This is a rubber gasket that seals the area around the dishwasher control panel or door edge, preventing moisture from escaping during wash cycles. It helps protect internal electronic components from water damage and maintains proper door sealing. Replace this gasket if you notice water leaking from the top or sides of the dishwasher door, or if the seal appears cracked, warped, or deteriorated.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

This repair parts list is a service parts diagram and itemized list that helps identify replacement parts for a specific appliance, speeding accurate parts ordering and repair planning. It's a reference sheet used by technicians and DIYers. What it does:

• Shows exploded diagram locations so you can visually identify the part you need
• Lists part numbers and quantities for components shown on the diagram
• Helps correct replacement parts before ordering or beginning repairs
• Useful for troubleshooting by comparing installed parts to the diagram

• This is a reference/documentation item, not a replaceable mechanical component
• Use the diagram to part numbers and orientation before ordering
• Keep the sheet dry and fold-free to preserve legibility

Mounting screw for dishwasher assembly. Secures internal components and panels. Replace if missing, stripped, or corroded during maintenance or repair.

Replacement care guide and operating manual for your dishwasher. Provides setup, usage, and maintenance instructions if original was lost or damaged.

This is an adhesive Energy Guide label that mounts on the appliance exterior to show the manufacturer's estimated energy use and rating. Replaces a missing, torn, or unreadable energy guide so ratings are clearly visible. What it does:

• Displays the appliance's estimated energy consumption and efficiency information.
• Restores required labeling if the original guide is damaged or removed.
• Helps homeowners verify energy rating details at a glance.
• Common symptom: label is missing, badly faded, or illegible.

• Surface must be clean, dry, and free of oils or residue before applying.
• Peel-and-stick installation; align carefully—adhesive is permanent and difficult to reposition.
• No tools required; follow the original label location and orientation for compliance.

6 - 10 x 3/8, pan plask, switch

Owner's manual for your dishwasher. Provides operating instructions, maintenance guidelines, and care information. Replace if lost or damaged.

Replacement mounting screw for dishwasher panels and internal components. Secures brackets and chassis parts. Replace stripped, missing, or damaged hardware.

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.