Parts for Maytag YMER8775AS0: 02 - Control Panel Parts

This is a push button located on the oven control panel, typically used for functions such as keep warm or other cooking settings. It presses into the control board assembly and activates the corresponding feature when pushed. Replace this button if it is cracked, broken, stuck, or has fallen off the control panel.

This machine screw is used across appliances to secure brackets, covers, and internal components. Replacing a missing or stripped fastener helps keep parts aligned and tight, reducing vibration and preventing loose or shifting assemblies.

• Provides machine-thread fastening for panels, brackets, and internal parts
• Helps eliminate rattling, vibration, and loose fits
• Restores proper attachment when the original screw is stripped, missing, or corroded
• Used wherever an 8-32 screw is specified in the service manual or parts list

• Disconnect power to the appliance; turn off gas/water if applicable
• Match the screw to the original location to confirm size and thread
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten to prevent stripping or cracking

Fix burners stuck on high heat or won't adjust temperature with this infinite switch. Common issue with multi-ring burners. Easy DIY repair in under 30 minutes.

Fix burners stuck on high or heating out of control with this infinite switch. Controls single, dual, or triple element burners. Easy DIY repair.

Burner stuck on high or won't regulate temperature? This infinite switch controls top burner heat settings. Straightforward DIY fix, 15-30 minutes.

This is the decorative bezel ring that surrounds a control knob on the range or oven front panel. It provides a finished appearance and helps seat the knob properly against the control panel surface. Replace this bezel if it is cracked, discolored, or missing, which can leave gaps around the knob area.

This is the main electronic control board that manages oven functions including temperature regulation, cooking modes, the clock display, and self-clean cycles. It receives input from the control panel and sends signals to heating elements, sensors, and other components. Replace this board if the oven fails to heat, displays error codes, has an unresponsive or erratic control panel, or if the clock and timer stop functioning properly.

Black left side end cap panel for electric and gas ranges. Replaces cracked, broken, or damaged side trim pieces. Installs on left exterior edge.

Broken indicator light lens? This red lens covers the control panel light opening, restoring visibility and protection. Easy DIY fix in under an hour.

Secures range components and panels to maintain proper alignment. Replace if your original bracket is cracked, broken, or missing to restore stability.

Protective cover that conceals your range's control box and wiring. Replaces cracked, broken, or missing covers to restore a finished look.

Heat shield for electric ranges. Protects components from heat damage. Replace if cracked, warped, or missing to restore proper heat protection.

Right side end cap panel for ranges in black. Replaces cracked, broken, or missing end panel. Covers and protects the exterior side of your range.

Replace your cracked, broken, or missing range control knob. Installs on the control shaft to restore heat level selection with secure grip and detents.

Size: 8-18 x 1/2 inch.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

Secures the control console assembly to your range, keeping the control board and interface stable. Replace if bracket is cracked, broken, or missing.

Secures wiring and components to prevent movement and disconnection in your electric range. Replace if clips are broken or wires are loose. Verify fit with your model number.

Replace your range's surface unit indicator light when it stays on, flickers, or burns out. Signals when burners are hot for safety. Verify fit.