Parts for Whirlpool CET8000AQ1: 01 - Control Panel Parts

Fix unresponsive buttons or a blank display with this laundry center control panel. Restores full cycle selection and settings control. Moderate DIY repair.

Dryer won't start or stops mid-cycle? This door lock assembly secures the door and engages the safety interlock. Straightforward DIY repair.

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

A short self-tapping screw used to fasten appliance panels and trim so components stay secure and aligned. Replacing a worn or missing screw restores proper fit and reduces rattling or loose parts. What it does

• Fastens panels, trim, and small assemblies to the appliance frame
• Keeps control panels, access panels, and bezels securely mounted
• Replaces stripped, rusted, or missing fasteners that cause vibration or rattling
• Helps maintain proper alignment of removable panels and covers

• One short self-tapping screw

• Disconnect power before working on the appliance to avoid shock or injury
• Use the correct screwdriver and hold parts in place while installing to avoid cross-threading
• Do not overtighten — stop when the panel is snug to prevent stripping or cracking
• Replace with the exact part number to ensure proper fit and function

This is a coin box used in commercial or coin-operated dryers. It collects coins deposited by users to activate the drying cycle. Replace this coin box if it is damaged, jammed, not accepting coins properly, or if the locking mechanism is broken.

This service access switch is the OEM-style replacement switch that detects and secures the appliance's service or control access point, helping technicians safely access internal components during diagnostics and repair. What it does:

• Detects whether the service/access panel or console is opened and signals the control board accordingly
• Helps prevent operation while the access panel is open for safer service
• Restores proper access-sensing when a worn or failed switch causes service-mode or control interlock issues
• Compatible where the appliance uses a dedicated access/service switch for control-board interlock functions

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove necessary panels or console to access and replace the switch
• Handle near control boards with care to avoid ESD damage; reconnect all wiring securely
• After installation, restore power and verify the switch correctly senses panel position and that the appliance operates normally

Access panel cover for laundry center. Replaces cracked, broken, or missing covers that expose internal components. Secures cabinet opening for clean look.

This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.

• Secures appliance components and panels in their mounting points
• Replaces damaged, stripped, or missing hardware
• Helps reduce rattling or vibration from loose parts

• Disconnect power; shut off water or gas supplies if applicable
• Match location with the original screw; start threads by hand to avoid cross-threading
• Tighten until snug; do not over-torque, especially into plastic or thin metal
• Reinstall any covers or panels and test for secure fit

Mounting bracket for laundry center units. Secures components in place during operation. Replace if cracked, bent, or missing to restore proper support.

Wire harness for laundry center units. Connects electrical components between washer and dryer sections. Replace if wires are frayed, damaged, or broken.

Wire harness for laundry center units. Connects electrical components between washer and dryer sections. Replace if wires are frayed, damaged, or connectors worn.

This is a cycle selector switch used in washer/dryer laundry center combos to choose wash or dry cycle settings. It connects to the control panel and sends the selected cycle signal to the main control board. Replace this switch if the cycle selector knob no longer clicks into positions, the machine won't start a selected cycle, or the wrong cycle runs when a specific setting is chosen.

This is the factory key that unlocks the unit's service access door, restoring proper access for maintenance and settings. Replace a lost, bent, or worn key to open the service door without damaging the lock or panel. What it does:

• Unlocks the service/access door on compatible units
• Restores access when the original key is lost, broken, or bent
• Helps prevent prying or damage to the door and lock
• Common symptoms: cannot open service door; key will not turn; missing key

• Service door key

• Disconnect power before servicing internal components after opening the door
• Insert the key fully and turn to release the latch; support the panel as it opens
• Do not force a key that won't turn—check for lock damage
• Store a spare key in a secure location to avoid downtime

Control panel bezel for laundry center units. Replaces cracked, broken, or discolored bezels around the control area. Restores appearance and finish.