Parts for Whirlpool RJE313PP: 03 - Control Panel Parts

A replacement mounting screw to secure appliance panels and components so parts stay properly fastened during normal use. Small but essential hardware for stable, rattle-free operation and reliable repairs. What it does:

• Fastens panels, brackets or components to the appliance chassis
• Prevents loose panels, vibration noise, or parts shifting during operation
• Used when original screw is lost, damaged, or stripped
• Restores proper fit and alignment after disassembly for service

• Disconnect power and water before starting any repair
• Use the correct screw type and length; do not force or substitute oversized fasteners
• Tighten until snug—avoid overtightening to prevent stripped threads or cracked parts
• Keep small parts away from children and pets

This is a genuine replacement screw used to secure panels, brackets, and components on compatible Whirlpool appliances. It restores proper fastening so loose parts stop rattling and panels stay aligned. What it does

• Fastens trim, panels, brackets, or mounting hardware to appliance chassis
• Helps stop vibration and rattling caused by missing or stripped fasteners
• Restores secure connections after repair or part replacement
• Matches OEM thread specification to fit intended mounting holes

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Start threads by hand and tighten until snug; do not overtighten
• Inspect mating threads and replace if damaged

Replacement bezel that fits around a control knob to restore a clean appearance and secure knob fit. Helps reduce knob wobble and protects the control shaft from dirt and spills for reliable knob operation. What it does:

• Covers the control shaft and provides a finished look to the knob area.
• Restores a snug, centered fit when the original bezel is cracked, worn, or missing.
• Reduces knob wobble and play that can affect control feel.
• Helps keep debris and liquids away from the control shaft to prevent interference.

• Disconnect power (unplug appliance or shut off circuit) before removing or replacing knobs.
• Remove the control knob, then pry or unclip the old bezel from the panel; install new bezel by aligning and snapping into place.
• Inspect for broken clips or mounting points; replace any damaged fasteners to ensure a secure fit.

The Surface Knob is an OEM part for Whirlpool ranges and cooktops. It allows users to control the heat level of the surface burners, providing precise adjustments for cooking. The knob fits securely onto the control valve stem, ensuring accurate and reliable operation.

Common causes of a bad surface knob include frequent use, physical damage from impacts, or exposure to high heat. A faulty knob can hinder your ability to control the burner accurately, affecting cooking performance.

Symptoms of a bad surface knob include:

• Difficulty turning the knob
• The knob not staying in place or slipping off
• Inaccurate heat control
• Visible cracks or damage to the knob

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This selector switch knob replaces a worn or missing control knob on a range/oven. It restores a secure, easy-to-turn grip on the selector switch so you can confidently choose functions when the original knob is cracked, stripped, or missing.

• Attaches to the selector switch shaft so you can select oven functions, depending on model
• Direct replacement for knobs that are cracked, stripped, loose, or missing
• Restores proper feel and control when turning the selector switch
• Common symptoms: knob falls off, hard to turn, heat-damaged or worn knob

• Disconnect power to the appliance to prevent accidental activation
• Pull the old knob straight off the selector switch shaft
• Align the shaft orientation with the new knob and press firmly until fully seated
• Verify smooth rotation and correct alignment with the panel markings

This infinite switch controls the variable heat settings for a cooktop surface burner, restoring adjustable heating for smooth cooking. It replaces a failed control to help the burner reach and hold selected temperature levels. What it does

• Regulates power to a surface element so heat changes smoothly from low to high.
• Common symptom: burner won't heat or only works on one setting.
• Common symptom: heat level won't change or is stuck at a single setting.
• Can cause clicking or intermittent burner operation when failing.

• Disconnect power to the appliance at the breaker before servicing.
• Confirm terminal locations and wiring match your original switch; label wires before disconnecting.
• Access typically requires removing the cooktop or control panel.

This latch knob screw secures the latch knob to its shaft on compatible appliances. Replace a missing, stripped, or rusted screw to restore a firm, reliable attachment and proper latch/knob operation. What it does:

• Attaches the latch knob securely to the latch mechanism/shaft
• Helps maintain proper door latch engagement and knob control
• Common fix for a loose, wobbly, or falling-off knob
• Replaces a lost, corroded, or cross-threaded screw

• 1 latch knob screw

• Disconnect power and allow the appliance to cool completely before servicing
• Align the knob on the shaft and start the screw by hand to avoid cross-threading
• Tighten with the correct screwdriver; do not overtighten to prevent damage
• The latch engages and releases smoothly after installation

This part has been discontinued and is no longer available.

This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.

• Provides a countersunk, flush-mount fastener for panels, trim, brackets, or covers
• Helps maintain alignment and secure attachment during operation
• Replaces stripped, rusted, or missing hardware
• Symptoms can include loose panels or handles, rattling noises, or visible gaps/misalignment

• Disconnect power (and shut off gas, if applicable) before servicing
• Match screw length and thread to the original for proper fit
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Support the part being fastened to keep alignment while tightening

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming

This part has been discontinued by the manufacturer and is no longer available.